Question about GE Washing Machines

1 Answer

My ge profile harmony washing machine has a message that says "a problem has been detected with this unit."

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 119 Answers

Washers - Harmony Washer Error Message or Code
The Harmony washer electronics can automatically determine if problems exist with the machine. Sometimes an error code can also be present because of things the machine cannot control: like changes in house voltage, water pressure, or temperature.

"A problem has been detected with this unit" will be displayed on the screen.

The most common solution for this message is to turn the machine OFF and then ON. However, this message will sometimes cause the control to stop the machine from working. With this type of error, the control panel will need to be reset. The following steps will allow you to reset your control.

Solution:

1. Clear the ERROR from the screen: Press and hold the MY CYCLES and BACK buttons simultaneously for 3 seconds. The control will display any recorded errors. Please write down what error codes are shown on your screen in case service is needed. If a MORE icon is displayed on the screen, press MORE to list additional errors. When the EXIT button appears, press EXIT.
2. Remove Power: Follow the onscreen instructions to remove power (unplug unit) and then immediately plug unit back in.
3. Clear Setup Mode: After power is restored, a setup screen that begins with "Congratulations..." will be shown. DO NOT PRESS the OK button shown at the bottom of the screen. Press the START/STOP and POWER buttons simultaneously until the Home Screen is displayed. Your unit is ready to function normally.


GOOD LUCK. TIMOTHY DO 714-334-1998

Posted on Aug 04, 2010

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 119 Answers

SOURCE: have a message on GE Profile Harmony washer that

Washers - Harmony Washer Error Message or Code
The Harmony washer electronics can automatically determine if problems exist with the machine. Sometimes an error code can also be present because of things the machine cannot control: like changes in house voltage, water pressure, or temperature.

"A problem has been detected with this unit" will be displayed on the screen.

The most common solution for this message is to turn the machine OFF and then ON. However, this message will sometimes cause the control to stop the machine from working. With this type of error, the control panel will need to be reset. The following steps will allow you to reset your control.

Solution:

1. Clear the ERROR from the screen: Press and hold the MY CYCLES and BACK buttons simultaneously for 3 seconds. The control will display any recorded errors. Please write down what error codes are shown on your screen in case service is needed. If a MORE icon is displayed on the screen, press MORE to list additional errors. When the EXIT button appears, press EXIT.
2. Remove Power: Follow the onscreen instructions to remove power (unplug unit) and then immediately plug unit back in.
3. Clear Setup Mode: After power is restored, a setup screen that begins with "Congratulations..." will be shown. DO NOT PRESS the OK button shown at the bottom of the screen. Press the START/STOP and POWER buttons simultaneously until the Home Screen is displayed. Your unit is ready to function normally.

Posted on Jan 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ge harmony washer says there is a problem been detected how do I clear it


The Ge washer claims it has detected a problem. How do I clear it? There doesnt seem to be anything wrong with the unit.

Aug 26, 2010 | GE Profile Harmony WPGT9360E 4.0 Cu. Ft....

2 Answers

Have a message on GE Profile Harmony washer that say " a problem has been detected with the unit" help?


Washers - Harmony Washer Error Message or Code
The Harmony washer electronics can automatically determine if problems exist with the machine. Sometimes an error code can also be present because of things the machine cannot control: like changes in house voltage, water pressure, or temperature.

"A problem has been detected with this unit" will be displayed on the screen.

The most common solution for this message is to turn the machine OFF and then ON. However, this message will sometimes cause the control to stop the machine from working. With this type of error, the control panel will need to be reset. The following steps will allow you to reset your control.

Solution:

1. Clear the ERROR from the screen: Press and hold the MY CYCLES and BACK buttons simultaneously for 3 seconds. The control will display any recorded errors. Please write down what error codes are shown on your screen in case service is needed. If a MORE icon is displayed on the screen, press MORE to list additional errors. When the EXIT button appears, press EXIT.
2. Remove Power: Follow the onscreen instructions to remove power (unplug unit) and then immediately plug unit back in.
3. Clear Setup Mode: After power is restored, a setup screen that begins with "Congratulations..." will be shown. DO NOT PRESS the OK button shown at the bottom of the screen. Press the START/STOP and POWER buttons simultaneously until the Home Screen is displayed. Your unit is ready to function normally.

Jan 15, 2010 | GE WPGT9360E Profile Harmony 4.0 cu. ft....

2 Answers

Message: a problem has been detected with this unit At first the washer would not spin up to speed which would leave water in tub and clothes wet at end of cycle. Now I get the above message??


My was doing the same thing. I went to GE's appliances website and found this solution. http://www.geappliances.com/search/fast/infobase/10011313.htm

I had to do it for both loads of laundry but it worked short term. I do believe I may need a repair man to check out the other possible causes that my machine displayed when I did the reset. Hope this works for you as well.

Oct 02, 2009 | GE Profile Harmony WPGT9360E 4.0 Cu. Ft....

2 Answers

Error message only prior to the rinse cycle,not filling correctl


The cold water solenoid valve seems to have failed on you. They're easy to replace and can be purchased at any appliance parts company

Jun 15, 2009 | GE Dryers

1 Answer

Won't continue cycle the message is ''Notice'' a problem has been detected with this unit.


Press and hold the my cycles button and the back button simultaneously for 3 seconds. This will reset the control panel and let you see any stored errors.

Mar 13, 2009 | GE Profile Harmony WPGT9360E 4.0 Cu. Ft....

1 Answer

Ge profile notice: a problem has been detected with this unit


hello: I have a its a GE PROFILE WPGT9350 washer and i have that pop up when i push power button what can i do if you can help this missg "Notice A problem has been detected with this unit if you can tell me how to get to Service Mode Diagnostics" thanks my email is mnunocortes@hotmail.com Actually I have tried unplugging it and letting it rest and plugging it back in, same message. Thanks anything can help

Feb 20, 2009 | GE Profile Harmony WPGT9360E 4.0 Cu. Ft....

3 Answers

A problem has been detected with this unit i need know how to enter my Service Mode Diagnostics


I'll email you a few pages out of a service manual for a WPGT9360 (closest I could find to your model number) hope this helps.

Nov 12, 2008 | GE Profile Harmony WPGT9360E 4.0 Cu. Ft....

2 Answers

GE Profile Harmony 4.0 -Broken Clutch Coupling


if your under warrenty always call for service repairing it yourself voids your warrenty

Jan 15, 2008 | GE Profile Harmony WPGT9360E 4.0 Cu. Ft....

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

487 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Tim Whalen

Level 3 Expert

3074 Answers

yadayada
yadayada

Level 3 Expert

76051 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...