Question about Televison & Video
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
I called Sharp and told them about our problem. At first they denied even knowing about this kind of problem but after some back and forth, they finally gave me a case number and told me to call back on Monday (this was on a Saturday). I did that and at first they didn't want to admit anything there either but again, after some back and forth, they agreed to have the set fixed by a local company (under contract with them I suppose). When the people called to tell us when they were coming we told them that they had told us that they would be there a few days later and the service people said 'yeah, but we got the part in sooner'. So what does that tell you? They do KNOW about this problem - it's just getting them to admit it. The service guy brought some new boards out but they didn't fit so they had to take the set in while they ordered new boards. That took almost 2 weeks but we've got it back now and haven't had any more problems with it. Our set was over 2 years old but I didn't know it at the time - I thought it was just over 1 year old. But we did give them the model and serial number and am happy with the way things turned out. We live in Texas so I don't know how anybody else's problems were handled.
Posted on Feb 17, 2009
SOURCE: LC-37AF3X Sharp Aquos KCD TV
If the TV goes in standby, then it is in protection mode.
Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box
Try first leaving the TV power cord unplugged for some times, let say one hour or so.
The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.
1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.
2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.
If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.
If you are in situation 2 , then there is an internal fault.
If under warranty contact the manufacturer ringing the number on the user manual
If you want to repair at your own expenses, just locate any good qualified repairer.
If you want to DIY you find parts here,
All: Appliance parts, electronics parts & more from PartStore.com
Encompass Parts Distribution
LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |
On LCD Pay particular attention at inverter and power board, power board can be inspected looking for bulged or leaking capacitors, then tested with a multimeter. The inverter is more difficult to test , there is need to read voltages, should be done by a tech. Also the LCD controller board can cause same problem
On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.
On Rear Projection : check lamp, lamp ballast, power board, and convergence.
On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.
Posted on May 05, 2009
Hi there. I hope you will see this reply. I bought one of these TV's yesterday and I've got the code from my dad's website www.satcure.net
If your remote is Version 6 then you will be able to follow the help on the sky box under
Then follow the steps using code 1221
If you have a Revolution 8 remote then you will have an easier job but with a 3 digit code.
3 digit code is 253
TO PROGRAM THE remote USING THE 3 DIGIT CODE:
1. Turn on the TV receiver
2. Press TV on the Sky Remote Control
3. Hold down SELECT and the RED buttons together for approximately two seconds, until the RED LED on the Sky remote blinks twice.
4. Enter three digit code from list for the receiver (early versions now flash twice).
5. Press select to enter code structure (the LED will flash twice if a valid code has been entered).
6. Now press the STDBY button and test other functions.
Hope this helps/works!
Posted on Jun 12, 2010
Tips for a great answer:
May 24, 2015 | Sharp LC-42SB45UT 42 in. LCD HDTV
Nov 20, 2014 | Sharp Lc-70le745u
Aug 27, 2014 | Sharp Lc-42sb45ut 42" - Active 42" Tv -...
Sep 24, 2010 | Sharp Aquos LC-45GD4U 45 in. LCD HDTV
Aug 19, 2009 | Sharp AQUOS LC-32D44U 32 in. LCD TV
Jun 17, 2009 | Sharp Aquos LC-32G4U 32 in. HD-Ready LCD...
Oct 21, 2008 | Sharp Aquos LC-46D62U 46 in. LCD HDTV
Oct 21, 2017 | LG Televison & Video
Oct 21, 2017 | Hisense Televison & Video
179 people viewed this question
Usually answered in minutes!