Question about Panasonic PT-50DL54 50" Rear Projection HDTV-Ready Television

1 Answer

How do i reset the hour timer on my PT-50DL54J

SAME AS ABOVE

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

TO RESET THE LAMP TIMER PRESS THE VOLUME DOWN BUTTON ON THE FACE OF THE TV AND THE OK BUTTON ON THE REMOTE AT THE SAME TIME FOR 6 SEC.

Posted on Apr 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need service manual for panasonic pt-50dl54j


You should be able to download a technical manual from this site.

Scroll down below the cover image and press on Download File link that shows up in about 10 seconds after opening the link.
PANASONIC CHASSIS GN1D PT 50DL54 PT 60DL54 DLP TECHNICAL GUIDE Service...

Aug 28, 2014 | Projection Televisions

1 Answer

How to reset the hour meter on a panasonic pt-52lcx16


Panasonic Projection TV Lamp Timer Reset
Your lamp will probably last a lot longer than the TV thinks it should. This procedure will reset the lamp timer so you don't have to look at that annoying message every time you turn your tv on. Remember that the "lamp" indicator light on the lower left of the set will stay on until the lamp is actually replaced. I had to buy a replacement lamp to get this information, could not find it anywhere for these model numbers.
Press the volume down button on the projection display and hold down the zero button on the remote control at the same time for more than 5 seconds. When the reset procedure is complete, a message will display that the lamp timer was reset to zero.
This procedure will work for Panasonic models: PT-52LCX66 , PT-56LCX66 , PT-61LCX66 , PT-52LCX16 , PT-56LCX16 , PT-61LCX16

Jul 20, 2014 | Panasonic PT-52LCX16

1 Answer

Replace lamp flashed today, how long til i lose picture pt 50dl54


It's a timer, it counts the passing of time. The timer does not indicate the condition of the lamp. You may have a day or a year. Best advise would be to have a lamp on hand for when the lamp failure does occur.

Apr 16, 2010 | Panasonic PT-50LC13 50" Rear Projection...

1 Answer

I am about to replace a DLP lamp. How do I reset the lamp time on a Panasonic PT-50DL54J, using a TY-2004 lamp?


This all probably comes a couple years too late, but when you install a new lamp, you’ll want to reset the hours on the counter your television has. Doing this will allow you to avoid getting any messages about the lamp needing to be replaced despite you having a new lamp inside your set.
If you need to get into the service menu, you can do so by following these directions:
With power on, hold down VOL minus button on projection display and hold down the PIP or SPLIT button (try both) on the remote simultaneously for more than 5 seconds.

Jan 31, 2010 | Panasonic PT-50DL54 50" Rear Projection...

1 Answer

I can't reset the hour counter and I have no sound


I can help you reset the lamp timer for your Panasonic PT-52LCX66 Projection HDTV.

The buttons used are the TV's volume down and the remote's number 0.

Follow the steps in my Fixya Tip for the complete lamp timer reset procedure.

As for sound, more info is required.

I hope that helps.

Dec 26, 2009 | Panasonic PT-52LCX66 Projection Television

1 Answer

I can't reset the the hour meter and i have no sound


I can help you reset the lamp timer for your Panasonic PT-52LCX66 Projection HDTV.

Follow the steps in my Fixya Tip for the complete lamp timer reset procedure.

I hope that helps.

Dec 26, 2009 | Panasonic PT-52LCX66 Projection Television

1 Answer

Pt-50dl54j after replacing the lamp i get a flashing green


chec to make sure lamp housing is in all the way make sure screws are tight.

Dec 17, 2009 | Panasonic PT-50DL54 50" Rear Projection...

1 Answer

How do I reset my lamp timer on a panasonic HDTV


go into menu.... and you will find lamp setting. reset it to zero hours

Nov 17, 2009 | Panasonic PT-50LC14 50" Rear Projection...

1 Answer

Resting my lamp?


Hold the Volumn Down button on the TV,
and the MUTE buttom on the remote for 5 seconds.

Jun 23, 2009 | Panasonic PT-50DL54 50" Rear Projection...

1 Answer

Reset lamp life counter pt-50dl54j


To reset the lamp timer, turn the TV on first. Now hold VOL DOWN on the TV and MUTE on the remote until a message appears on the screen about the lamp timer being reset. Make sure the remote is pointed toward the TV to receive the signal.

Feb 19, 2009 | Panasonic Projection Televisions

Not finding what you are looking for?
Panasonic PT-50DL54 50" Rear Projection HDTV-Ready Television Logo

Related Topics:

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

Josh Whitehead
Josh Whitehead

Level 3 Expert

1146 Answers

The Knight
The Knight

Level 3 Expert

68408 Answers

Are you a Panasonic Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...