Question about Belkin Wireless G Plus MIMO (F5D9230-4) Router (1010835)

2 Answers

How to set a password for the router thanks - Belkin Wireless G Plus MIMO (F5D9230-4) Router (1010835)

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 708 Answers

Step 1: Connect your computer - Router ( Wired)

Step 2:Make sure that the wireless is disconnected in the laptop

Step 3:Open Router setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 4:On the left under wireless click Wi- fi protected setup

Step 5:Leave the Password blank and click submit

Step 6:Disable it and click apply changes

Step 7:On the left under wireless click security

Step 8:Selected the security mode as WPA / WPA2

Step 9:Type a password in the blank field ( Pre Shared key or PSK )Make sure that the password is a minimum of 8 characters

Step 10:On the left under wireless click channel and SSiD

Step 11:Change the Wireless Channel to 6

Step 12:Change the SSiD to a different name

Step 13: Click Apply Changes

Step 14:Unplug the power cord from the router

Step 15:Plug it back After 15 seconds

Step 16:Now try to connect to the new network


Goto belkinrouters.blogspot.com for more

Posted on Aug 03, 2010

Testimonial: "thx it was helpful regards Adnan Merza"

  • 1 more comment 
  • Rakesh Warrier
    Rakesh Warrier Aug 12, 2010

    It was a pleasure Assisting You

    For more ... Gotohttp://belkinrouters.blogspot.com

  • Ram Gopal
    Ram Gopal Sep 26, 2010

    Step 1: Connect your computer - Router ( Wired)

    Step 2:Make sure that the wireless is disconnected in the laptop

    Step 3:Open Router setup by typinghttp://192.168.2.1 on the address bar of internet explorer

    Step 4:On the left under wireless click Wi- fi protected setup

    Step 5:Leave the Password blank and click submit

    Step 6:Disable it and click apply changes

    Step 7:On the left under wireless click security

    Step 8:Selected the security mode as WPA / WPA2

    Step 9:Type a password in the blank field ( Pre Shared key or PSK )Make sure that the password is a minimum of 8 characters

    Step 10:On the left under wireless click channel and SSiD

    Step 11:Change the Wireless Channel to 6

    Step 12:Change the SSiD to a different name

    Step 13: Click Apply Changes

    Step 14:Unplug the power cord from the router

    Step 15:Plug it back After 15 seconds

    Step 16:Now try to connect to the new network

  • Ram Gopal
    Ram Gopal Sep 26, 2010

    Step 1: Connect your computer - Router ( Wired)


    Step 2:Make sure that the wireless is disconnected in the laptop

    Step 3:Open Router setup by typinghttp://192.168.2.1 on the address bar of internet explorer

    Step 4:On the left under wireless click Wi- fi protected setup

    Step 5:Leave the Password blank and click submit

    Step 6:Disable it and click apply changes

    Step 7:On the left under wireless click security

    Step 8:Selected the security mode as WPA / WPA2

    Step 9:Type a password in the blank field ( Pre Shared key or PSK )Make sure that the password is a minimum of 8 characters

    Step 10:On the left under wireless click channel and SSiD

    Step 11:Change the Wireless Channel to 6

    Step 12:Change the SSiD to a different name

    Step 13: Click Apply Changes

    Step 14:Unplug the power cord from the router

    Step 15:Plug it back After 15 seconds

    Step 16:Now try to connect to the new network

×

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 65 Answers

Step 1: Connect your computer - Router ( Wired)

Step 2:Make sure that the wireless is disconnected in the laptop

Step 3:Open Router setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 4:On the left under wireless click Wi- fi protected setup

Step 5:Leave the Password blank and click submit

Step 6:Disable it and click apply changes

Step 7:On the left under wireless click security

Step 8:Selected the security mode as WPA / WPA2

Step 9:Type a password in the blank field ( Pre Shared key or PSK )Make sure that the password is a minimum of 8 characters

Step 10:On the left under wireless click channel and SSiD

Step 11:Change the Wireless Channel to 6

Step 12:Change the SSiD to a different name

Step 13: Click Apply Changes

Step 14:Unplug the power cord from the router

Step 15:Plug it back After 15 seconds

Step 16:Now try to connect to the new network


Goto belkinrouters.blogspot.com for more

Posted on Sep 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a dlink dir 655 and lost my password. how can i get a new one?


For setting up your resetting d-link router password you have to follow these steps..
1. open your browser and type 192.168.1.0 and type user name and password
2.go to wireless settings and setup ssid ( network name ) and password
3. than click save and apply for more technical help you may can contact d-link Tech Support
i hope this will help you thanks

Oct 04, 2013 | D-Link Xtreme N DIR-655 Wireless Router

1 Answer

Getting a new router password for linksys e1200 se up disk


For that connect your router to computer with ethernet lan cable then you can access it with below ip address in internet browser.http://192.168.1.1 or http://192.168.2.1 Type as user as "admin" and password as "admin" or blank or "password" or "1234" then you can see configuration page of router.Click on wireless settings enable it if you want to set password security then enable WEP and enter password then you can connect it.Enable DHCP and Set WAN settings and internet service provider then save settings and restart router .Let me know if you need further assistance.Thanks for using FixYa.

Oct 19, 2011 | Cisco Linksys E1000 WirelessN Broadband...

2 Answers

I need to set a password for my Linksys Wireless-G WRT54G Router, but the websited 192.168.0.1 to set the password isnt working. I need help ASAP. Thank-You


to access the router page for linksys, you need to type 192.168.1.1 on the address bar. username is " admin " password is " password " if it doesnt work, try "admin" for username and "admin" for password. then it would take you to the router page. and you can start configuring.

Sep 09, 2011 | Linksys Wireless-G WRT54G Router

1 Answer

I cannot use my dlink router, because i forgot my username and password. Hope that you can help me. your immediate response is highly appreciated. thank you


You need to RESET router press RESET / WPS button for 10 seconds then all settings defaults . You can also configure it with below method.
Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. Then click on WAN settings set it as your internet service provider settings enable DHCP Then click on wireless and enable it. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. then connect cable from your internet provider to WAN port of router. Let me know if you need further assistance. Thanks for using FixYa.

Jun 22, 2011 | D-Link DIR-600 Router

3 Answers

I need to reset or find my origional password. Please help. Thanks


If you have changed the default password, you need to reset the router to the factory settings to get in with the default user and password (user admin and password as password, or if that doesn't work try 1234 - these are the default password for NetGear routers). Note that you will lose the ISP settings and wireless settings when you reset the router.

Here's a video on how to reset the router to the factory default settings: http://kbserver.netgear.com/media/flash/training/Troubleshooting/NG_WGR614V9Router_TS_LostPassword.html

Feb 17, 2011 | NetGear DG834G Router

1 Answer

Change router settings


hi,

in the browser type 192.168.1.1 and insert your login and password. if you have not change the login name and password then visit to your manufacturer site for default login name and password.... Usualy default login name and password is "admin".....This page will lead you to the router settings....

Hope this has helped you..
Thanks...

May 15, 2010 | 3Com OfficeConnect Wireless Router

1 Answer

When i set up the router i gave a password but


If you want to change the password to access the router you can open your browser and put in the address 192.168.1.1 (unless you changed it) and press enter. You should be prompted for a user name and password. Leave the user name section blank and put in the password for the router. Once you have logged into the router successfully, you will see the Administration tab. Click on it and you will be able to change the router password. Save the changed and close the browser window when you are finished.
If you need to change the Wireless Internet password, you can click on the Wireless tab, go to Wireless security and change the passphrase there too.
I hope this helped. Thanks for using FixYa.com!!

Apr 18, 2010 | Linksys WRT54GP2A-AT Router (WRT54GP2AAT)

1 Answer

Forgot password how to reset the password .


Is there any computer online using the router.
If not then you will need to connect the computer to the router.
If yes then you can open the router set up page on that computer.
router set up page is the page where you can check all the router settings.

Click Here for more information about the routers and network

Apr 02, 2010 | Belkin (F5D7230-4) Router (587009)

2 Answers

What is linksys wireless -g broadband router factory name and password


Factory user name as "admin" and password as "admin" or blank or "password"
If above user name and password doesnot work then you need to reset it .
Press RESET button for 10 seconds.
RESET button is in back side of router.
Let me know if you need further assistance.
Thanks for using FixYa.

Dec 25, 2009 | Linksys Wireless-G WRT54G Router

Not finding what you are looking for?
Belkin Wireless G Plus MIMO (F5D9230-4) Router (1010835) Logo

Related Topics:

394 people viewed this question

Ask a Question

Usually answered in minutes!

Top Belkin Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2260 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18394 Answers

Are you a Belkin Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...