Question about Sony Xplod XM-554ZR Car Audio Amplifier

1 Answer

Sony xplod 500w 4/3 channel

My amp shuts off at high volumes. my rockford fosgate Hx2 dvc 4ohm is the only speaker connected to it. the speaker is wired for 4ohm and is connected to the amp bridged at the rear channels. why does the amp shut down?

Posted by on

  • santell44111 Dec 07, 2008

    i have the same problem with my sony explod amp approx. 40 watts a channel. the rear chan bridged to a mtx 10 inch sub, the usb starts to distort and the whole amp shut down. if i disconnect the sub and just play the front spkrs it plays fine but no sub.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 631 Answers

If the speaker is a 4 ohm DVC (two 4 ohm coils), you can't wire it to get a single 4 ohm load. Try connecting one coil to each of the two rear channels. It may not be as loud but the amp should operate without going into protection.

If the two 4 ohm coils are in parallel, the amp is driving a 2 ohm mono load. That's probably why it's shutting down.

Posted on Apr 26, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Could u bridge this amplifier?


Yes. From 4 channel it will become 2 channel but will only accept 4OHM loads. There should be designated connections on the speaker terminals of the amplifier. dreamsystems

Feb 25, 2011 | Rockford Fosgate Power 800.4 Car Audio...

1 Answer

Can i power 2 12 subs a rockford punch z and a xplode with this amp i found all this **** in my garage and i need to know if it will power all this


First of all. Using two different kinds of sub woofers, is not an option, as these two sub woofers have different specifications and you should never mix sub woofers. Now the better choice from the 2, would probably be the Rockford. (cant be sure without knowing the models, power handling is also a factor in how well either of the sub woofers will play, but Rockford as a rule makes better sub woofers than Sony does) In my opinion, both the sub woofers deserve a better amplifier than what Boss has to offer. However to connect either of these sub woofers, you would need to determine how many voice coils it has and how many OHM the voice coil/s are. If it is a DVC (dual voice coil) and each voice coil is 4 OHM or 2 OHM, then you can connect one voice coil to one channel of the amplifier and the other voice coil to the other channel of the amplifier. If it is a DVC 2OHM you can also connect it wired in Series/Series to give a 4OHM load and should be connected to the BRIDGE dedicated speaker outputs of your amplifier. If it is a SVC (single voice coil) and it is 4 OHM, then you can connect the sub woofer to the designated speaker outputs of your amplifier that states BRIDGE. DO NOT run the amplifier in BRIDGE mode at 2 OHM as this will probably damage the amplifier. dreamsystems

Feb 18, 2011 | Boss Blade BL700 2-Channel Amp - 300W...

3 Answers

How do I hook up one sub to my rockford fosgate p3001 amp


Hey i have looked over many rockford manuals,(i own a 300.1 my buddy owns a 325.1) and for there mono(.1) amps there hooked together on the inside so channel A+ and B + are cencted on the inside the amp. So you ither hook one 2ohm sub to channel A or you can hook 1 4ohm subs to channel A and 1 4ohm sub to channel B. There 2ohm stable so any lower will eventualy burn the amp out.

Jan 08, 2010 | Rockford Fosgate P3001 Car Audio Amplifier

2 Answers

I installed a sony 600watt amp and it works but old rockford fosgate 200 hit harder how do i make my amp louder and evenly spread throughout my car


Hello jmanbutt99,

The old Rockford-Fosgate was probably producing the rated power. The Sony is most likely overrated. But, it's supposed to be stable on each individual channel down to 2 ohms and will deliver 65 watts RMS into that load. So to get the most from it, your best bet would be a pair of 4 ohm speakers paralleled to each channel. A relatively efficient speaker like the Kicker 07DS600's shown here should provide pretty good sound.

http://www.crutchfield.com/p_20607DS60/Kicker-07DS600.html?tp=105

These will work with as little as 6 watts RMS and can handle up to 50 watts RMS so the Sony should power them really well. They're 4 ohm so a pair in parallel will present a 2 ohm load.

Hope this helps

Oct 30, 2009 | Sony Xplod XM-554ZR Car Audio Amplifier

2 Answers

How many svc subs at 4ohm does it take to get this amp to 1ohm stable and can you reccomend a good sub combo for this amp whether it be dvc or svc


It depends if your sub is 4ohm svc, or 2ohm svc. 4ohm would take 4 subs wired in parallel, 2ohm would take 2 subs wired in parallel. But for a amp that big, subs that'll handle it are definitely gonna be dvc. I'd recommend 2 Orion 4ohm dvc hcca's. They come in either 15in or 12in. the 15s are louder if you have the space for them. As far as wiring goes, wire the voice coils on the subs in parallel to 2ohm per sub, then wire the 2 subs in parallel to 1ohm. Goodluck and congrats on the equipment, Orion is about as good as you can go for subs and amps. just be ready to lay down some dynamat cuz this system'll bloww your vehicle apart! good luck...

Oct 08, 2009 | Orion 2500D Car Audio Amplifier

3 Answers

It has an A and B channel for spkrs and i have one spkr bridged. do i split the neg to side a and pos to side b or just use one of the channels?


Could you elaborate on how the speaker is bridged?

I think you want to hook up a single speaker to a stereo speaker output.

In this case, you would strap (bridge?) the right and left speaker terminals by running a short wire from A right negative to A left negative. Then strap A right positive to A left positive -- this will give you mono output on either of the right or left speaker terminals -- connect your speaker to either one of these.

Do you know what the ohm rating is for the speaker outs on the amp and also the speaker itself?

Charlie

Aug 31, 2009 | Rockford Fosgate P3001 Car Audio Amplifier

2 Answers

Rockford fosgate amp keeps shutting down when volume is cranked


your cd player cant handle all the power, time to upgrade to a cd player with at least 80w10

Jun 12, 2009 | Rockford Fosgate Punch P5002 Car Audio...

1 Answer

Is this ok?


Yes it sounds like it should work.

Jan 06, 2009 | Car Audio & Video

1 Answer

Is this ok?


yes 2ohm should be fine for that amp no problem

But dont bridge it any lower than 2 ohms.

Nov 26, 2008 | Rockford Fosgate Punch P4004 Car Audio...

Not finding what you are looking for?
Sony Xplod XM-554ZR Car Audio Amplifier Logo

Related Topics:

396 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Car Audio & Video Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

xxxxxx xxx

Level 3 Expert

4724 Answers

Larry Stiles
Larry Stiles

Level 2 Expert

286 Answers

Are you a Sony Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...