Question about Airlink 101 AR675W Green 300Mbps 80211n Wireless LANFirewall 4Port Router
It is a relatively simple process to use the router as an access point. Follow these procedures:
1. Assuming the router is still at the default settings, connect the router to your computer using a patch cable from your computer to any of the lan ports on your new router, then enter 192.168.2.1 in your browser's url window and press enter (your computer must be setup to pick up ip addresses automatically). You might need to restart your computer.
2. enter admin for both user name and password in the router's logon window
3. click on network on the left and then select lan
4. enter a new unique ip address for the router that is the same as your local network (e.g. if your local ip is 192.168.100.105 then enter 192.168.100.200)
5. make sure the subnet is the same as your local network (e.g. 255.255.255.0)
6. disable DHCP on the router and click on Apply
Now connect the router to your network using a patch cable from your existing router to any of the lan ports on the new router. Connect your computer to the network. Thats it, you are done.
Posted on Aug 04, 2011
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Tips for a great answer:
The reason why people use a Encore wireless repeater is because some wireless remote client computers are out of range from the main network's access point (wireless router), or the wireless client is in the dead spot or the device you want to share to the network have no wireless interface card.
The function of a wireless repeater is basically to extend the wireless signal coverage. Wireless repeater does not authenticate, screen, secure, connect to the internet, give IP address to clients, broadcast names, etc., these are the wireless router's job. Repeater only repeats what the main wireless router does to the wireless clients.
1. Hooking up hardware connections:
As of this moment your repeater is not connected to any router or network. It has to be configured further to be able to be connected to your current network and access point router.
3. Connecting your Repeater to your existing network access point or router:
If you are using Windows 7 and your existing access point security wireless is set to WPA2 (AES), make sure your Windows 7 wireless security type properties is set to WPA2-Personal. To check go to Windows 7 Wireless Network Connection, look for your REPEATER router, right-click on it then click Properties, check the settings in the "Security" tab.>
When checking the wireless site survey, you may see two routers with the same SSID (names), these are your Access Point and the REPEATER tied together. This also means you are within the reachable range of both Access point and REPEATER.
5. To check the Repeaters user interface
At this moment, the Repeater is invisible to any client. The client's IP address is drawn from the DHCP server most likely to be also your wireless router. Therefore the IP address of the repeater is also invisible to the clients. Follow steps below:
May 15, 2012 | Encore Enhwi-2an3 Wireless-n Router
If you have an existing network, chances are you have already
configured network services on the network. In this case, you would use
the router as a pure Access Point to extend the range of your network by
allowing more attachment of wireless and wired computers. You MUST
also turn off the DHCP server on the router if there is a DHCP server running to
avoid IP address conflict.
To configure the router as an Access Point with the
DHCP server disabled:
Click the Basic Settings tab on the top navigation bar.
Select Access Point Mode.
Click the Next button.
Click OK to dismiss the DHCP disabled message
box (The DHCP server will be disabled in Access Point Mode by default).
Advanced Settings tab on the top
Click the Advanced IP Settings tab on the
left navigation bar.
Assign an IP address to the Wireless Broadband Router.
NOTE: The IP address should be reserved by the DHCP server. The Wireless Broadband Router cannot act as a DHCP client, therefore, it needs a static IP address for its LAN interface.
Save & Restart button.
Note the status bar at the bottom of the screen.
While the Wireless Broadband Router resets, the Power
light on the front of the
When your web browser returns to the main page of the
Wireless Broadband Route, the device has successfully restarted with the new
NOTE: The main page may not return if you have changed IP address of the router in Step 8. To view the main page, type the new IP address of the router in the web browser to access it.
Plug an Ethernet cable from the existing local
network into any LAN
port on the Wireless Broadband Router.
Jul 01, 2011 | Dell TrueMobile 2300 Wireless Router...
Mar 25, 2011 | Computers & Internet
Feb 17, 2018 | Belkin Surf N300 Wireless Router...
If you need more help come back.Post /
thumbs / testimonial are
Nov 30, 2010 | D-Link DIR-300 Wireless Router
Nov 29, 2010 | 2wire (2701HG-B) Wireless Router
Jan 14, 2010 | Samsung BD-P3600 Blu-Ray Player
Jan 02, 2010 | NetGear WGT624 Wireless Router
Jun 21, 2009 | D-Link DI-634M Wireless Router (DI634M)
Jan 14, 2009 | HP Compaq Evo n610c Notebook
179 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: