Question about Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Red light on left side says control locked Can not get machine to work, held cancel button in and then shut power off still not working

Posted by on

  • bandaid1 Aug 02, 2010

    it worked

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,515 Answers

Hi,

This is a very bad error. Unplug the washer for few minutes, say 30 minutes and then turn it ON, If the problem persists, you need to replace the control board.

Note - There is one tricks that might fix the problem :-

Step 1 Press any of the buttons on the control panel to see if the buttons are operational or check to see if the "Control Locked" indicator light is lit. If the control panel is operational, you may mistakenly lock the door.
Step 2 Press and hold the "End of Cycle Signal" button for approximately three seconds until the "Control Locked" indicator light shuts off. The control panel is now unlocked, and the washer is ready for use.
Step 3 Lock the washer again by pressing and holding the "End of Cycle Signal" button until the "Control Locked" indicator light turns on.

Good Luck!!

Thanks!!

Posted on Aug 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my washer stop working in the middle of wash cycle and then go dead and no response?


Should get some one to look at it. If there is a hot smell could be a short someplace.

Dec 22, 2016 | Kenmore Washing Machines

2 Answers

Lock Light Blinking


silly question but did you try holding the control lock button(perhaps its the heated dry button) in for 3 secs???? sonds as if the CONTROL LOCK has benn activated( child lockout)

Jan 14, 2009 | Kenmore 24 in. 15932 Built-in Dishwasher

1 Answer

The control lock light is on


there is a button on the far rt of the face of the machine...you hold that button down. the button is called end of cycle signal.
ann

Jan 06, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Control locked butten is on and no other buttons will work. Tried powering off for 5 mins and back on. Unplugged as well. Held down cancel button and all others for 10 full seconds timed....still...


the button you need to push and hold is the cycle signal. its at the bottom button on the far right side. push and hold until the light goes off, it most likely will take more than 3 seconds. The button your looking for should also have a small icon of a padlock .hope this helps

Dec 03, 2008 | Washing Machines

2 Answers

''Control Lock'' won't ''unlock''


Press and hold the "End of Cycle Signal" button to lock or unlock the control panel. The instructions should be printed directly below this button. I hope this helps you.

Nov 14, 2008 | Whirlpool Duet GHW9150P Front Load Washer

3 Answers

Control lock light on-door opens-won't start


Press 'control' + 'pause:lock' +
'temperature' for 5 seconds
OR
'end of cycle' for 5 seconds. Tell me which worked & rate me pl.

Apr 16, 2008 | Whirlpool GHW9150 Front Load Washer

5 Answers

Kenmore dishwasher Lock On light flashing


holding the button for four seconds will not do it, you have to hold it until the light stops blinking and
will go back to normal, normall takes more than four seconds to unlock the unit, this is something
the sears repair techs know becouse the are trained on all this things but, they will not share this things, becouse thats how they make money

Dec 29, 2007 | Dishwashers

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal DeAngelo

Level 3 Expert

2180 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...