Question about Dishwashers

1 Answer

My Maytag NDB9601 will not start any cycle. You can select the cycle and the display will show the time, but the start and delay buttons, located on the front, not the top with the cycle buttons, will not activate. This leads to the dishwasher not working at all. It worked in the morning, but not in the evening. Dishwasher is 1 year old.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Contributor
  • 68 Answers

Sounds like a possible door switch problem.

If you take that area of the door apart, check the ribbon cable for keypad. You can clean the connector with a pencil eraser.

Posted on Apr 25, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Model ESL 499. Why doesn't it start?


You have activated the delayed start function. Please read following instruction from user manual.

8. Delayed Start button

Allows the start of the programme to be delayed by a minimum of 1 hour, up to 9 hours. How to set the delayed start When the button is pressed, the number appears in the display (4). Press the button again to select the number of hours by which you wish to delay the programme start, up to a maximum of 9. E.g.: if you have selected number , the wash programme will start in 2 hours' time. To cancel the delayed start set, press the button until the number appears. Close the dishwasher door to start the countdown: a long audible signal (about one second) informs you that the function is active. If you open the door again you will see, in the display (4), how long there is to go (in hours) before the programme starts. A flashing dot in the digital display means that the delayed start function has been activated. Opening the door has no effect on a countdown which has already been started. If, during the countdown, you wish to see the programme number selected in the display, press the Programme Selector button (5). If, after having started the countdown by closing the dishwasher door, you wish to cancel the delayed start, press button (9) (Cancel) for about 2 seconds until the short «instruction accepted «signal is heard».

Dado

Sep 16, 2015 | Electrolux Dishwashers

1 Answer

What does Ho1 mean on the screen?


Some Bosch dishwashers have a time delay option. The H01 indicates a one hour delay has been selected. Press the Delay key several times until you see H00 in the display. Then try to start the dishwasher cycle you need. Bosch error codes tend to start with E.

Please add a comment with the model number of the dishwasher if you need additional help. (Without the model number, I can't be sure which key sets the time delay. On some models, the key is near the On/Off button. On others, it's closest to the Start button.) I hope this helps.

Cindy Wells

Sep 03, 2015 | Bosch Dishwashers

1 Answer

Reset button maytag dishwasher


  • 1 Open and close the dooricon1.png of your Maytag dishwasher.
  • 2 Locate the "Rinse" button on the dishwasher control panel. Press and release the button five times in quickicon1.png succession.
  • 3 Press and release the adjacent "Drain/Off" button on the control panel two times; this will deactivate the dishwasher's demo mode and reset your dishwasher.
  • If you need to restart your dishwasher or forgot some dishes and want to open it during a cycle and restart it

  • 1 Press the "Cancel Drain" button on the display. Allow about 2 minutes for the dishwasher to completely drain.
  • 2 Choose a cycle under "Cycles" on the panel.
  • 3 Select an option or options under "Options" on the panel.
  • 4 Push the "Start Resume" button.
  • Oct 24, 2013 | Dishwashers

    1 Answer

    Dishwasher ran all night still not finished. Error code 4H displaying.


    Hi and welcome to FixYa. I am Kelly. The 4H is indicating your dishwasher is in the delayed wash start mode. Here is some information from Sears about what to do:


    • The number letter combination indicates that the dishwasher is in a "Delay Start" mode, as well as how many hours were set for the delay start.
    • The dishwasher will not start the wash until it reaches the delayed hour that it was set for. Example: 1H = 1 hour delay start, 2H = 2 hour delay start, etc.
      • To start the dishwasher immediately and not wait for the Delay Start time, cancel the "Delay Start" option, by pressing the Cancel button. Then program the cycle and options and press Start.
      • To start the dishwasher after the Delay time, select the cycle and options desired. Select the "Delay Start" option and on some dishwashers it requires, pressing the Start button.
      • Some dishwashers will display a countdown of the delay time on the display.
    Note: Refer to the Owner's Manual or Use & Care Guide for specific instructions on using the "Delay Start" feature.

    If you need more assistance we will need your exact model number in any of your future responses.
    Thanks for choosing FixYa,
    Kelly

    Jan 04, 2011 | Dishwashers

    1 Answer

    Dish washer does not turn on CL light stays on when reset count down 6 appears then goes to CL


    Hello and welcome to Fixya,

    I have a ton of service info on Bosch so it`s best I post you an exert from the service pdf`s I have on my PC which will explain the meaning of "CL" and then go from there. This is not a common indication of a control problem, but it could be a problem with the plastic casing which houses the control, we`ll deal with that later.

    I`ve underlined the section pertaining to the "CL", this is for the SHU68** dishwashers only.

    TO OPERATE:

    First depress the On/Off Button until it locks in place.

    Once the On/Off Button is depressed the LED above the previously used cycle will illuminate.

    To change the cycle, simply press the desired Cycle Button twice. The LED above that cycle will then illuminate.

    The Cycle Countdown will display an approximate run time for the cycle chosen.

    This run time will depend on incoming water temperature and the turbidity of the pre-wash water.

    Note: It is normal for the Countdown Display to remain at a time increment for more than one minute, or skip a time increment depending on the calculations of the Control Unit. Also, with continued use the Control Unit will learn the wash and temperature patterns for the most commonly used programs and will then reduce the overall start and running times.

    At the end of the cycle the display will show a CL, indicating that the cycle is complete.

    **TO CANCEL A CYCLE:
    Press the Scrub Wash and Delicate / Econo Buttons both in at the same time. The unit will then drain and the figure CL will appear in the display.**

    DELAY START:
    The Delay Start feature allows the unit to be delayed for up to nine hours. To program, start the unit as described above, but after selecting a cycle push the Delay Start button. The display will show a 1h, or one-hour delay. Continue to depress the Delay Start Button until the desired delay time is reached (up to nine hours, 9h).
    The unit will begin automatically once the delay time has elapsed. To reset the delay, press the Delay Start Button until it reaches 0h.

    TOP RACK ONLY:
    The Top Rack Only feature can be used in conjunction with any cycle. To active, press the Top Rack Only Button after selecting a
    cycle, the Top Rack Only LED will illuminate and all water will be diverted to the upper wash arm for the complete cycle.

    REFILL RINSE AGENT LED:
    The Refill Rinse Agent LED is activated via a Reed Switch on the Detergent Dispenser, Section 4, Fig. 8-3. The LED will
    illuminate when the Rinse Agent Dispenser is empty.
    Service note: The Refill Rinse Agent LED will also illuminate when the dishwasher door is opened and then
    closed even if the Dispenser is full, but will only remain lit for a few seconds.

    “F” CODE:
    An “F” in the display window indicates a filling fault.

    Please note: If the door is opened during the cycle, the On/Off Button will be reset to off and must be depressed again to re-active the cycle. The cycle will resume from where it left off.

    Now that you are equipped with this info, what I`d suggest is trying the **cancel option. ( ** see above )

    Once you`ve tried the cancel option, select a Regular Wash and post back what happens and I`ll try to assist you from there.

    Good luck.

    macmarkus :)


    May 14, 2010 | Bosch 24 in. SHU6802UC / SHU6806UC...

    1 Answer

    Multiple lights are lite when running a cycle....can't run certain cycles (bulky items, whites etc) spin light continuously blinks. have tried unplugging and restarting with no results


    I feel you may have a Control Board issue. I would see if the Control Board will let you into Service Mode. If it does I would read the Diag code blocks 1 thru 40. The block only show up when an error event has been logged.

    Bottom line I see no easy way out without least swapping out the Control Board for a start point.

    You will need the FAV6800A/FAV9800A Service Manual to get started. See page 17 of the SM TO READ THE Diag codes

    FAV6800A/FAV9800A Service Manual for reference. Sears Parts Direct for reference.

    Here is a quick start if the Control Board will let you into Service Mode;
    To enter Service Mode press and hold simultaneously the Enviro Plus and Spin Only keys until the machine beeps and the LED display reads 00.

    From the Service Manual;

    Display Diagnostic Codes
    The diagnostic code display can be toggled on and off from Service Mode by pressing the Wrinkle Control key. The display will show a “d”. The diagnostic codes can be viewed by using the Set Delay Time arrow keys. The Set Delay Time down arrow key will cycle down the list one code at time each time it is pushed. The Set Delay Time up arrow key will cycle up the list one code each time it is pushed. The first time the Set Delay Time down arrow key is pushed, the newest code will be displayed. A code generated during or after the current cycle will be displayed with the rightmost dot “.” turned ON. Access Other Features While a diagnostic code is displayed, if the Normal

    If you decide to give it a try jot down the code blocks and toss them back to us for review.

    The Control Board p/n 25001217

    Another vendor Clothes Washer Control Board - 25001217

    Good Luck Rich

    Dec 29, 2009 | Maytag Neptune FAV6800AW Top Load Washer

    1 Answer

    Bosch SHU 6800 Water hot at sink only luke warm at the washer


    BAD CONTROL BOARD TO TEST TO SEE IF THIS IS THE ISSUE RUN TEST PROGRAM
    To start test program, press and hold both SCRUB WASH and DELICATE/ECONO program buttons, then turn unit on by
    pressing ON/OFF button. Initially, control module version # will be displayed (e.g./ “20” = version 0 without jumper). When
    wash program buttons are released, lights above them will flash. To end test program, press ON/OFF button.
    To check each program indicator light, press its button. To check Cycle Countdown display, Refill Rinse Agent light and
    REGULAR WASH light, press REGULAR WASH button (press Delay Start button to test Cycle Countdown display
    alone). Cycle Countdown display will show "88" when REGULAR WASH button is pressed and "8h" when Delay Start
    button is pressed.
    To start testing, press both SCRUB WASH and DELICATE/ECONO buttons a second time. When testing has ended,
    Cycle Countdown display will show a fault using codes below. If more than one fault occurs, code numbers will be added
    together, (e.g./ “6” = faults 2 + 4).
    0 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault
    1 = Aqua Sensor ("Sensotronic") fault 4 = Filling fault F = Filling fault (display occurs during wash, not test)
    To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil,
    measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays
    at ~ 1.5-2 A, then heater, high limit or flow switch are faulty.
    If water level switch (f1) has failed (opened), display will show fault code "4" and unit will continually fill and drain where
    testing won't be completed. If flow switch (e5) has failed (opened), display will show "0", water won't heat (to 150ºF) and
    water won’t stop circulating. If NTC probe (f2/f4) has failed (opened), display will show fault code "8" immediately and
    testing will end shortly after water has started circulating

    Jul 18, 2009 | Bosch 24 in. SHU43 Built-in Dishwasher

    2 Answers

    Water is not coming into my Maytag dishwasher.


    Hi,
    Is the door open or unlatched?Make sure the door is completely closed and latched. On models with a dual-digit display, the control displays "- -" during a cycle if the door is not latched. Check for obstructions (spoons or utensils), that may be interfering with the door operation. A lower dish rack that is installed backward will also cause incomplete door closure. The lights for cycles selected will flash if the door is opened while running a cycle.
    Is there power to the dishwasher?Check your household electrical box to see if a fuse has blown or if the circuit breaker has tripped. If the unit has a plug-in power cord, make sure it is plugged in.
    Does your dishwasher have a rotary timer knob?The cycle selection must match the position of the timer knob. Turn the timer knob to the beginning of the preferred cycle. The timer knob should click when you reach the start of the cycle.
    Is the control lock option activated?
    The indicator light next to the lock graphic will illuminate when the controls are locked. Press and hold the Heated Dry option (button with lock icon) for three seconds and the light should turn off. Instructions are also placed on the label on top of the inner door to unlock the controls.
    Is the delay start option activated?To cancel the delay and cycle, press Start/Cancel twice.
    Is the water shutoff valve turned on?Make sure that the water shutoff valve is turned on.

    Mar 03, 2009 | Maytag 24 in. MDB6600A Jetclean II...

    2 Answers

    I need to disable my ovens auto shut off


    The control is automatically set to turn off the oven after 12 hours baking or 3 hours broiling should you forget and leave the oven on. If you want to remvoe this feature do the following steps: 1. Press and hold, at the same time, the BAKE and BROIL buttons for 3 seconds, until the display shows "SF". 2. Press the DELAY START TIME button. The display shows "12Shdn" for 12 hour shut off. Press the DELAY START TIME button again. The display will show "no Shdn" for no shut off. 3. Press the START button.

    May 21, 2007 | Kenmore 33464 / 33465 / 33469 Gas Single...

    1 Answer

    Maytag quiet series


    My manual says: 1- Close door. 2- Select cycle. 3- Press delay. 4- Push Start/Cancel. (As soon as start/cancel is pressed, the flashing should stop and the delay time will begin).

    Mar 12, 2007 | Maytag 24 in. MDB5600A Jetclean II...

    Not finding what you are looking for?
    Dishwashers Logo

    Related Topics:

    116 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dishwashers Experts

    Mike Cairns
    Mike Cairns

    Level 3 Expert

    3053 Answers

    yadayada
    yadayada

    Level 3 Expert

    70387 Answers

    Brad Brown

    Level 3 Expert

    15133 Answers

    Are you a Dishwasher Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...