Question about Dishwashers

1 Answer

Hose is clear but it will not pump the water out?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,073 Answers

If the pump is running check the pump for blockage

Posted on Apr 25, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fisher paykel troubleshooting


Lights 1, 3 & 4 flashing implies it still full of water and won't continue the cycle because it hasn't pumped out the water. It's often caused by a blocked outlet hose at either the pump end or the sink end. Check the sink end first an ensure it clear but if not, empty out all the water, turn it upside down and remove the base cover. only about six screws. Unclip the hose at the pump end and ensure it's clear. Blow through it as hard as possible to test if the hose is clear. If this doesn't work, the pumps probably faulty and will need replacement. Unsure of the cost but it's nearly all plastic and very cheap looking!

Jul 14, 2014 | Fisher and Paykel Dishwashers

1 Answer

How to use back wash


backwash is easy. dont let it scare you.
here are the steps:
-turn off pump
-roll out backwash hose
-push down on handle and rotate to backwash
-turn pump back on
-depending on type of filter, run for minimum 2 minutes (watch discharge water. run until it is clear) if there is a glass vial, you can watch that until water is clear.
-turn off pump
-push down on handle and rotate to rinse
-turn on pump and run for 30 seconds (water will leave discharge hose)
-turn off pump
-push down handle and rotate to filter
-you can run pump immediately

May 20, 2014 | Hayward SAND FILTER, PRO SERIES

1 Answer

Amana nfw7300ww00 wont drain. pump basket is clear pump runs but not pushing the water out. pump hose is clear


You may have blockage up b4 pump need to remove hose from outer tub and clean out or pump is bad and just spinning motor you hear prop is stripped

Jan 30, 2013 | Amana Washing Machines

1 Answer

What does E20 mean


The E20 error code indicates a problem with water drainage. Inspect the drainage hose for kinks that could impede the drainage flow. This frequently occurs when the machine is pushed up against the wall without allowing room for the hoses. If there are no kinks, the hose is probably clogged. Carefully detach the hose from the machine, and use a garden hose to force water through it. If the water doesn't pass through, use a plumber's snake to clear the clog. If there is no clog, inspect the drain pump for clogs. Unplug the machine, and open the small rectangular door towards the bottom of the front of the machine. Drain the pump through the emptying hose into a container until the water flow stops, and rotate the pump impeller to clear any foreign objects. Close the pump and restart the cycle. If the problem persists, contact a service center.

May 18, 2012 | Zanussi ZWF1430W Front Load Washer

1 Answer

I have a hotpoint first edition wma11 which is not draining and water is still left in the drum when the cycle has finished. Any ideas as to what the cause of the problem is and how this can be...


first check outlet hose at sink end grease can build up on connection at trap under sink,if this is clear first dcoop out as much water from drum and lay outlet pipe flat into low basin to syphon water out ,when drained make sure the machine is isolated,take off lower back panel if you look in you will see black sump hose attached from bottom off drum to pump remove sump hose from drum by undoing clamp and insde is plastic float ball check to see if anything is blocked if clear re attach and remove pump take off pump housing (three screws) check if anything is in pump if clear change pump

Sep 08, 2011 | Washing Machines

1 Answer

Fisher & Paykel GW611 Excellence does not pump water out. All lights are on and when it is suppose to pump, you can hear the noise, but no water coming out of the hose!


It sounds like the drain pump or the diverter valve is restricted. Check to make sure that the drain hose is clear then disconnect power and lay the machine's front on a padded surface to access the drain pump and the diverter valve at the bottom of the tub. Remove the pump's inlet and outlet hoses then check and clear from any debris that may prevent water from draining out. Check the impeller for any damage or restriction.

Check the diverter valve for the same condition as the pump described above. T
he diverter valve is where the drain pump and the recirculation pump inlet hoses are attached from. Make sure the valve is in the drain position while the drain pump is working. Replace the drain pump and/or the diverter valve if deemed necessary.

Jul 18, 2011 | Fisher and Paykel Fisher & Paykel Washer

1 Answer

Maytag neptune front load washing machine will not fully discharge water after the rinse cycle...HELP???


Check the drain hose and clear it from any debris that might be blocking the water from draining out completely. If the drain hose is clear of debris, check and clean the pump. Disconnect the machine from the power outlet before servicing for safety purposes.

Remove the rear access panel to access the pump and disconnect the wiring harness from the terminals of the drain pump and the pressure switch.

Loosen the clamps holding the drain hose and the tub hose to the pump assembly. It is a good idea to spread a towel under the pump before loosening the clamps.

Remove the hoses and rotate the pump assembly counterclockwise to release the pump assembly support legs from the keyed slot in the base of the washer. Remove the pump assembly from the washer.

Clear the pump impeller from any debris that might be causing it to work improperly. Clean the tub and the drain hose.

Reassemble the pump, the hoses, and reconnect the wires to the terminals of the pressure switch and the drain pump. Reinstall the rear access panel and run the machine.

Replace the pump (part #25001052) if water still do not drain out completely.

Remove the plastic bag covering the pressure switch. Press in the locking tabs on the back of the pressure switch and pivot the pressure switch off the pump bracket.

Grasp the pressure switch and lift the nipple of the pressure switch from the pump cap.

Install the pressure switch into the new pump assembly in reverse of the steps above.











Feb 24, 2010 | Maytag Neptune MAH6500A Front Load Washer

1 Answer

Windshield wiper water


The washe pump is a known item that will fail, especially if the washer fluid froze one time. If the hoses are all clear, replace the washer pump motor.

Apr 05, 2009 | 1998 Toyota Corolla

2 Answers

Aquarius wash system plus wm 63


First of all lay the drain hose into a bowl or bucket to drain off.
Then take off the plate at the back of your machine and you will see a pipe running from pump to drum.
Where it meets the drum there is a filter inside which you can check for debris. also take off at the pump and check inside pipe & pump.
Happy to help further if required.
Thankyou for using Fixya.

Jan 29, 2009 | Hotpoint Aquarius WMA42 Front Load Washer

2 Answers

Fluff in drum blocking pump


Hi.

You will probably have to remove the hose from the drum to the pump to clear the blockage.

access is from the rear.

Nov 23, 2008 | Bosch Classixx WVF 2402 Front Load...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

yadayada
yadayada

Level 3 Expert

70346 Answers

Brad Brown

Level 3 Expert

15107 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...