Question about JVC KD-G230 CD Player

1 Answer

Demo wont go away

I have followed each step in this manual but nothing happens. I hold down the select button and then push the round track button but still nothing. Any advise?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Hold the sel button until the display says demo. Release the sel button and wait for the display to read demo on. Turn the volume knob counter clockwise.

Posted on Sep 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Aiwa CDC-x204 stuck in demo mode


This is what worked for me:
  1. Power the radio off (hold the power button in top left corner in for several seconds)
  2. Remove face plate
  3. Hold in reset 10 seconds
  4. Press push-menu dial/button 3 or 4 times
  5. Insert cd and hit source to switch to tuner before cd starts
Not all of these steps may be necessary.
I suspect having the power off before the reset button was the important part.

Jul 24, 2012 | Car Audio Receivers

1 Answer

Sony CDX-S2210 CD Player stuck on demo mode , cant adjust volume eq, skip track or anything


make sure the unit is switched off and the clock is displayed then

1 Press and hold (SEL).
The setup display appears.
2 Press (SEL) repeatedly until the
desired item appears.
3 Press the volume +/– button to select
the setting (example “ON” or “OFF”).
4 Press and hold
(SEL).
The setup is complete and the display returns
to normal play/reception mode.
Note
Displayed items will differ, depending on the source
and setting.
With the card remote commander
In step 3, to select the setting, press
< or ,.
The following items can be set (follow the page
reference for details):
“z” indicates the default settings.
*1 When the unit is turned off.
*2 When the audio output is set to “SUB.”
CLOCK-ADJ
(Clock Adjust)
(page 4)
BEEP To set “BEEP-ON” (z) or
“BEEP-OFF.”
SUB/REAR*1 To switch the audio output.
– “SUB” (z): to output to a
subwoofer.
– “REAR”: to output to a
power amplifier.
DIM (Dimmer) To change the brightness of the
display.
– “DIM-ON”: to dim the
display.
– “DIM-OFF” (z): to
deactivate the dimmer.
DEMO*1
(Demonstration)
To set “DEMO-ON” (z) or
“DEMO-OFF” (page 4).
A.SCRL
(Auto Scroll)
To scroll long displayed items
automatically when the group/
track is changed.
– “A.SCRL-ON”: to scroll.
– “A.SCRL-OFF” (z): to not
scroll.
LPF*2 (Low
Pass Filter)
To select the cut-off frequency
“78HZ,” “125HZ” or “OFF

Jan 28, 2010 | Sony CDX-S2210 CD Player

1 Answer

I want to know how to take the radio out of DEMO mode, and set the clock. I have no manual


http://www.fixya.com/support/p446590-jvc_kd_g720_cd_player/manual-19657/page-14

hold select, use next/prev track button to scroll thru options: go to demo, turn knob to switch setting to off, press select to accept

Mar 23, 2009 | JVC KD-G720 CD Player

1 Answer

Install setting for Clock and Calendar


http://www.pioneerelectronics.com/pio/pe/images/portal/cit_11221/429287552DEHP7900BTOperationManual0328.pdf

Your Owners manual

Setting the date
The calender display adjusted in this mode appears
when the telephone source is selected
or sources and the feature demo are off.
1 Use MULTI-CONTROL to select
Calendar.
2 Push MULTI-CONTROL left or right to
select the segment of the calendar display
you wish to set.
Pushing MULTI-CONTROL left or right will select
one segment of the calendar display:
Day—Month—Year
As you select segments of the calendar display
the segment selected will blink.
3 Push MULTI-CONTROL up or down to
set the date.

Setting the clock
Use these instructions to set the clock.
1 Use MULTI-CONTROL to select Clock.
2 Push MULTI-CONTROL left or right to
select the segment of the clock display you
wish to set.
Pushing MULTI-CONTROL left or right will select
one segment of the clock display:
Hour—Minute
As you select segments of the clock display
the segment selected will blink.
3 Push MULTI-CONTROL up or down to
put a clock right.
Note
You can match the clock to a time signal by
pressing MULTI-CONTROL.
! If the minute is 00 to 29, the minutes are
rounded down. (e.g., 10:18 becomes 10:00.)
! If the minute is 30 to 59, the minutes are
rounded up. (e.g., 10:36 becomes 11:00.)

Jan 01, 2009 | Pioneer DEH-P7900BT CD Player

6 Answers

Stuck in demo


I had the same issue and was about to give up.
cleaning, key combos and such didn't work out.

Solved the dirty way, as described some comments above:

"Just took the faceplate from the "push-menu" button and hit it against a hard surface [not too hard but not too soft hits] and thats it, it worked again."

ah, the good manners!

Jun 07, 2008 | Aiwa CDC-X504MP CD Player

4 Answers

CDC-X304 in permanent DEMO mode


I HAVE SAME PROBLEM. AFTER I REPLACED MY DEAD BATTERY MY AIWA CDC-X304 IS STUCK IN THE DEMO MODE. ONLY CD WORKS BUT ALL BUTTONS ON FACING DO NOT RESPOND. ANY SUGGESTIONS HOW TO RESET.

Jan 16, 2008 | Aiwa CDC-X304 CD Player

3 Answers

KDC-X591 Demo Mode & Remote Steering Harness


instructions i was trying to figure out the same thing in my brothers car and i came to this site the two answers before mine were both right and wrong, they needed to be combined and modified a tic. but i just got my brothers kdc x591 and this is how hit source button till standby mode is on, press menu then use the control knob the right one thats not the volume, to select demo mode press the 1 button then menu and voila

Dec 31, 2007 | Kenwood KDC-X591 CD Player

2 Answers

Jvc kdg162


Make sure you have hooked up your memory power wire to a source of 12 volts that does not go away when the ignition switch is turned off. I suspect that is your problem. Your main power wire will of course need to go cold when the ignition switch is turned off.

Dec 01, 2007 | Car Audio Receivers

3 Answers

Stereo stopped responding


1. While in Demo mode push and hold the "PUSH-MENU" button until "set" appears on the screen.

2. push "Seek" + or - to select Demo

3. turn "PUSH-MENU" to select "demo off"

Oct 30, 2007 | Aiwa CDC-X204 CD Player

5 Answers

Unable to turn off DEMO MODE


1. Turn Radio On
2. Change Source input to Stand-By
( Puts radio in display only Stand By mode.)
3. Press Menu Button
( Gives you standby menu)
4. Toggle display with control knob until DEMO ON appears
5. Hold control knob in until DEM0 OFF appears
6. Press Menu Button
7. Change source back to music.
All done. same as other Fixes - Just step by step!

Sep 09, 2007 | Kenwood KDC-MP435U CD Player

Not finding what you are looking for?
JVC KD-G230 CD Player Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Car Audio Receivers Experts

kakima

Level 3 Expert

96627 Answers

xxxxxx xxx

Level 3 Expert

4706 Answers

Radames Pagan
Radames Pagan

Level 3 Expert

196 Answers

Are you a JVC Car Audio Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...