Question about Belkin (F5D5231-4) Router

1 Answer

Unable to conect to dodo isp

My friend just purchased a belkin 4port where do we type in the isp phone number so as the modem can connect to the internet

Posted by on

  • serra baby
    serra baby May 11, 2010

    hello



    -- is dodo your internet service provider?

    -- is it a cable? dsl? or adsl connection?

    -- aside from isp phone number do you have a username and password from your isp?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

First make sure that you have a valid connection to the router and that you have a valid IP address.

(note: for a wired connection you should have a link light on the numbered port of the router to which your computer is connected. You should have an IP address in the range 192.168.2.x. To check your IP address, click on Start, Run and type in command. Click OK. Now type in ipconfig and hit enter. Your IP address will be listed.)


For the F5D5230-4, F5D6230-3

Open a Web Browser
1. In the address bar type http://192.168.2.1
2. Click on Intial Setup
3. Select PPPOE and click Select
4. Type in your username that was assigned to you by your ISP *
5. Type in your password that was assigned to you by your ISP twice
6. Leave Service Name blank
7. Click on Enter
8. Click on Status in the left hand column
9. It should now show Cable / DSL Connected under the Internet column

For the F5D5231-4, F5D6231-4, F5D7230-4, F5D7231-4, F5D7231-4P, F5D8230-4, F6D3230-4

Open a Web Browser

  1. In the address bar type http://192.168.2.1
  2. Click on Connection Type in the left hand column under Internet WAN heading
  3. Enter your password if any and click Submit
  4. Click on PPPOE and then click on Next
  5. Type in your username that was assigned to you by your ISP *
  6. Type in your password that was assigned to you by your ISP twice
  7. Leave Service Name blank
  8. Click on Apply Changes
  9. Click on the Home link at the top of the screen
  10. It should now show Connected as the Internet Status at the top right hand corner of the web page

Posted on Jun 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My laptop wont log on to belkin


Sir,

Check your IP Address, Maybe its conflict with other device.

My advice to turn it automatically.

Or

Installing your Belkin router is still possible even without using its Setup CD. You can set up your router manually through the web-based setup page of the router.

Perform the steps below to set up your Belkin router through the web-based setup page.

NOTE: images may vary depending on the router model or computer you are using.
Power cycling the modem and router
Step 1:
Unplug the modem and router from the power source.
Step 2:
Connect the modem to the WAN or Internet port of the router.




7a2d9691-2d05-4a84-8c84-2dbd7c1da14f.png

Step 3:
Power ON your modem first, then your router by plugging them back to the power source.
Manually setting up your router
Step 1:
Connect the computer to one (1) of the Ethernet ports of the router.


53d87d4f-f0e2-4bc0-a2ee-20571d20d693.png

Step 2:
Launch a web browser and enter "192.168.2.1" in the address bar.

caaa1424-71a1-4705-a257-5c83bb988d1a.png

Step 3:
Click Login.

f43cf160-b3ef-4848-ae4a-ae3797a563b4.png

Step 4:
Leave the Password field blank and click Submit.

40e8d69f-22a6-4f6b-8eaa-2446bf156833.png

Step 5:
Under Internet WAN, click Connection Type.

7e28a43e-cefa-485a-923d-5d6ae2c6fce0.png

Step 6:
Select your Connection Type, then click Next.

d93ad37d-1fb2-41b6-b1ca-8a5e9a5d8c4b.png

NOTE: If you don't know your Connection Type, contact your Internet Service Provider (ISP). To know how to set up your router according your ISP, refer to the links below:
Cable Internet Service
PPPoE / DSL
Static IP Account
Step 7:
Enter the details provided by your ISP and click Image.
You should now be able to connect to the Internet. To verify, Internet Status on the upper right corner should read Connected.


116f45be-cc94-4208-82b8-1afa55cb7ea5.png

You can also launch a web browser and go to your favorite website or try visiting the Belkin Site for more information and support on your devices.

as mention On official Belkin website vedio for Belking Online Support:
Setting up the Belkin router using an iOS device Video

Belkin

Or

In case you still need assistance then follow us for Belkin Tech Support on:Belkin Support

Mar 07, 2014 | Belkin N Wireless Modem-Router F5D8633au4A

Tip

How to Configure Belkin routers for Centurylink, Embarq, Bell sympatico, Bell...


How to Configure Belkin routers without installation CD for Centurylink, Embarq, Bell sympatico, Bell Canada ISPs ?
Configuring Belkin routers without installation CD for Centurylink, Embarq, Bell sympatico, Bell Canada ISPs :
  • Connect the Computer to the Router in one of the 4 ports named wired (usually grey in color) using an Ethernet cable.
  • Do not connect the modem to the router.
  • Open internet explorer / Firefox / chrome or any of your default web browser.
  • In the address bar type the default gateway address of Belkin router i.e., 192.168.2.1
  • Belkin router setup page (RSP) will be displayed.
f7dd033.jpg
Wired Part Configuration:
We need to configure the wired part by following these steps.
Step 1: You need to LOGIN to the router for making any changes. (No login password, just leave it blank and click SUBMIT)
Step 2: Click on LAN settings (found on left side of RSP), change the IP address from 192.168.2.1 to 192.168.40.1 and save changes.
Step 3: Now Connect the DSL Modem to Router in the port named Modem (usually yellow in color) using another Ethernet cable.
***Once you are done that, you need to re-login to RSP by typing the new IP address 192.168.40.1 in the address bar of web browser.

Step 4: Check for the internet status at the top right hand corner of RSP. If it is connected then the wired part is working perfect with the router (wired computers will go online). Need not follow the steps below, directly jump to wireless part configuration.
Step 5: If the Internet Status is not connected then, click on CONNECTION TYPE (found on left side of RSP), it has to be selected as DYNAMIC and click next. It will ask for HOST NAME, leave it blank or you can type anything there and click on APPLY CHANGES.
Step 6: Now check for the internet status at the top right hand corner of belkin RSP. If it says connected then everything for the wired part is configured perfectly. You can go ahead and configure for the wireless part.
If it is not connected then we need to do a network power cycle.

Steps to be followed for performing Network power cycle:
  • Unplug the power cable of both your modem and router.
  • Wait for 30 seconds.
  • Plug back the power cable of the modem and wait until all the lights are lit up in it.
  • Now plug back the power cable to the router and check for the lights in the router.
Modem & Internet lights will be lit and they will be solid (blue/green) in the router; it says that the Internet status is connected. Now you will be able to go online in the wired computers.

If still Modem & Internet lights are not solid in the router; it may be blinking in red/ amber it says that the Internet status is not connected. You will not be able to go online in the wired computers.

In this case you need to connect your computer directly to the modem and check whether you are able to go online. If you are not able to go online, then you need to contact your ISP and fix your issue with internet.

The above method is applicable only for Embarq, century link, Bell Sympatico, Bell Canada ISPs. Because these ISPs will have the IP address same as Belkin routers....

If nothing works then you need to contact your ISP and ask them to bridge the modem...Bridging the modem disables NAT in the modem and allows you to get a public IP in the modem.
click here to configure wireless part...

on May 09, 2010 | Routers

2 Answers

I've been using the Belkin N1 router using it for my wireless connection for almost 3 years now. But only last night, the wireless light is out, and the security light is out as well. I've tried unplugging...


I think the power cable of your modem has been damaged. kindly check the power cable. If there is no light on the modem , it is assumed to be that the power cable has been damaged. so you have to purchase the power cable of the modem. If the power cable is found to be perfect , kindly purchase the net work cables/ OR prepare the net work cables if you are aware of about the network cables., because the clippings of the network cables might have spoiled. If the power cable of modem, network cables are found to be perfect , it is certainly , the modem might have damaged. To fix the all the problems mentioned above , you are requested to to contact your ISP ( Internet Service Provider) . They will certainly fix your problems. In the mean while kindly try to solve yourself. If you are paying rent towards the monthly charges against the modem to ISP , they must be replace your modem with new one. If you have purchased the modem by paying the cost of the modem at the time of installation of the internet connection , you have to purchase the new modem, if the old modem was found to be damaged.

Oct 03, 2010 | Belkin (F5D8231-4) Wireless Router...

1 Answer

Trying to connect Belkin G wireless router to mac


No Issues at all !!!
As I Dont know who your ISP is , before starting the installation collect these information

1 : The connection Type

2 : If it is PPPoE then the user name and Password

Step 1 : Connect router - Computer ( Wired )

Step 2 : Open RSP By Typing 192.168.2.1 on the address bar of safari

Step 3 : On the left side click Connection type under Internet WAN

Step 4 : Leave the password Blank and click submit

Step 5 : Choose the connection type As per your ISP

Step 6 : Click next

Step 7 : On this page Enter the Information that has been given by the ISP

Step 8 : Click Apply Changes

Step 9 : Check What is the Internet Status on the Top Right hand Side

Step 10 : If it Is Connected then you will have Internet

Step 11 : If it is No Connection then

Step 12 : Unplug the Power Cable from the Modem And the Router

Step 13 : Plug the Power Cable back to the Modem
And wait until All the Lights Are Back

Step 14 : After all the Lights Are ON in the Modem
Then Plug the Power Cable back to the Router

Step 15 : Check The internet Status

Step 16 : If it is not working then
CALL : 1800-223-5546

Jan 03, 2010 | Belkin Routers

1 Answer

My ISP is Embarqmail.com (not listed) so I checked


If it is Belkin Then You will need to do the following steps

Step 1 : Connect The Router - Computer ( Wired ) And make sure the modem is not connected to the router at this time

Step 2 : Open RSP By typing 192.168.2.1 on the address bar of internet explorer

Step 3 : On the left hand side click LAN Settings

Step 4 : Leave the password blank and click submit

Step 5 : Change the IP Address into 192.168.3.1

Step 6 : Click Apply changes

Step 7 : Open RSP By typing 192.168.3.1 on the address bar of internet explorer

Step 8 : On the left side click Connection type under Internet WAN

Step 9 : Leave the Password Blank And Click Submit

Step 10 : Choose the Connection type As ( Make sure you get the Connection type right , Contact your ISP About this ) Dynamic \

Step 11 : Click Apply Changes

Step 12 : Connect Modem - Router
Check the Internet Status

Mostly this will work




Dec 29, 2009 | Belkin Routers

1 Answer

Sharing a connection with wired and wireless computers


i just have a question, do you have an internet connection when your computer connected to your modem(the device provided by your Internet Service Provider)? Possible that the Belkin not working is that maybe you don't have internet from ypur ISP.

I suggest you to connect your computer first to the modem, turn off the pc and afterwards the modem, after 2 minutes, turn on the modem first, when all lights stable, turn on the pc and check if you can go online. If not, better contact your ISP first for them to check the connection. If everything working fine with your ISP. Reply to this post again and provide the following information.

Your ISP?
Brand of the Modem?
Brand of the Belkin Router?
Type of Connection you have form ISP, DSL or CABLE?
If DSL, please make sure that you have a username and password from your ISP?
How many computers do you have?
What is the Windows Version your using or the Operating System?

Thanks.

Sep 29, 2008 | Belkin (F5D7231UK4) Wireless Router

1 Answer

Set up my belkin g router


You may have to configure the belkin router depending on the type of ISP that you have.

Basically, you can do these to configure your router:

1. connect the computer to the numbered port of the router and connect the modem to the internet/WAN port.

2. turn off the modem, router and the computer for 30 seconds

3. turn on the modem first, wait for the lights to stabilize then turn on the router, wait for the lights and lastly turn on the computer.

Sep 04, 2008 | Belkin (F5D7230-4) Router (587009)

1 Answer

Belkin N1 Router connection drops when phone rings


You may have a phone line connected from the modem to a wall outlet. Count the number of cables coming out of your modem - you should have only three: the power cable (connects to the wall), Cat 5 (also connects to the wall), and ethernet (running from the modem to the router).

Nov 09, 2007 | Belkin (F5D8231-4) Wireless Router...

Not finding what you are looking for?
Belkin (F5D5231-4) Router Logo

Related Topics:

907 people viewed this question

Ask a Question

Usually answered in minutes!

Top Belkin Routers Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

steve morris
steve morris

Level 3 Expert

1673 Answers

Christopher Thrash

Level 3 Expert

425 Answers

Are you a Belkin Router Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...