Question about RTO LifeCore Fitness LC-T900HR Treadmill

1 Answer

I have the Lifecore Fitness T900HR treadmill and when my husband is running it stops. We have made sure all the connections are tight even the safety key but it still stops. When I am using the treadmill walking it does not stop with me. When is stops with him, he gets and Error 1 message. I looked in the owners manual and there is not information on error messages.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • RTO Master
  • 832 Answers

Their might be high friction between the belt and deck thus causing the error 1 code when your husband is on it. Try lubricating the area between belt and deck using silicone lubricant ( refer to owners manual). Then the lighter of the two "aka wife" walk on the treadmill for about 5 to 10 minutes.
This should take care of the problem if not then their is an issue with the belt and deck ( 85% of problems on treadmills are belt and deck related)

Posted on Jul 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to an Expert (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bladez prisma treadmill error e1 replaced lower control board and speed sensor


I will answer my own problem here, maybe it will help someone else. After BH North America customer service told me I needed a new lower control board and I had to spend $100+, it wasn't the board. Then they said it was the speed sensor, they sent that out for free, that wasn't it. Now, they would not respond to me. So, we went off the troubleshooting guide saying it was a connection problem between the upper and lower board. My husband opened up the "leg" of the treadmill and checked the connections (cutting the tie cords that hold the wires tightly in place, maybe too tightly and that's what caused them to come unplugged) and now the belt runs! So, BH got another 100 dollars of my money, on top of the original $800 and solved nothing and then ignored my emails. Horrible customer service and when this one finally bites the dust, I will never purchase a machine from them again. P.S. This treadmill is only approx. 2 yrs old.

Feb 12, 2013 | Bladez Fitness Prisma Supra Folding...

1 Answer

Hyperextension jn-1360 type h 6136004 error Er o2 comes up after 20 sec running and then stops


1) Adjust the speed sensor see the diagram, clean it, and tight the connector very well.
2) test the input voltage motor, if there are the motor need repair,se my personal TIPS
3) test the output voltage board, for input voltage motor, if there are NOT the board is faulty. see the block
4) Run the software caibration for diagnostic, troubleshooting, and fix it.
God bless you
9_21_2012_1_03_28_pm.gif9_21_2012_1_03_52_pm.gif

Sep 20, 2012 | Bh Fitness T8 Basic Treadmill

1 Answer

I have a vision fitness treadmill T9250 and now the console display isn't working properly. Some of the


Dear Sir:

Please see the diagram attached from REED switch, adjust, clean, and tight the connector wires very well.

2) change the batteries by new ones, use the best.clean the contact batteries.

3) tight the ribbon cable from keypad .+ tight the connector from display board vs lower board.

4) after you fix it RUN THE sofware calibration for diagnose, troubleshooting, See my personal tips for help

sincerely. God bless you
5_3_2012_12_57_12_am.gif

Apr 30, 2012 | Vision Fitness T9250 Deluxe Folding...

1 Answer

I bought a used Life Fitness 95T from a fitness center, the display displayed "please replace safety switch to continue workout". The Magnetic switch is in place but the unit does bot recognize...


If the console takesbatteries, replace them. If this does not work or your console does not requirebatteries, check the reed switch or optic sensor. Reed Switch:Unplug the treadmill and remove the motor hood cover. The reed switch is mountedon the frame next to the front roller pulley. There is a magnet glued into thefront roller pulley. When adjusting the reed switch, make sure it is pointingdirectly at the magnet. Move the tip of the reed switch within 1/8" of themagnet. Also, check to see that the wire is not damaged, and is connected tothe console. 11_30_2011_11_41_39_am.gifThen tight the flexible cords from keypanel vs display board( clean the keypane with spray from contact cleaner. then tight the connector from display board vs main motor controller. Remember the main motor controller has aprox 90% of functions of any treadmills. See the block diagram that I did for people like you, And now you will get powerful strong resultant what is wrong. sincerely. Good luck.

finally 2 options: 1) display faulty 2) Main motor controller of course after you did the first step.

11_30_2011_11_44_50_am.gif

Oct 08, 2011 | Life Fitness 95Ti Treadmill 95 Ti

1 Answer

Lifecore r100 rower shows error2


I quote this description directly from manual...

zjlimited_1191.jpg

Hope this helps. Good luck.

May 06, 2011 | Kettler Lifecore Fitness R100 Apm Premier...

1 Answer

I have a Horizon fitness CST3 and the belt stops running but everything else stays on. Do you know what is cuasing my problem?


How old is your treadmill? Has the deck been lubricated? Do you smell anything odd when the belt stops? Unplug treadmill, remove motor cover and check cables are all connected.

Oct 23, 2010 | Horizon Fitness Merit Fitness 725T...

2 Answers

I have a error reading of l5 or ls not too sure york fitness z16


Hi,

The L5 message means that there is a problem with the speed setting switches. Some models have one set of speed adjusting stitches on the handlebar and another set on the console. One of them is defective and is causing the problem.

Dec 29, 2009 | York Exercise & Fitness

1 Answer

Life fitness treadmill display: transistor error-won't run


This error shows up if motor controller detects a failed part. This isn’t a reset-able error. Treadmill will not allow workouts until serviced.
Solution
Main motor wires/leads could be disconnected at the start of a workout. If the motor is properly connected and in working condition then the drive transistor could have failed. Check Motor Controller.

Feb 28, 2009 | Life Fitness Remanufactured Next...

1 Answer

Replace Switch error message


It was the emergency tag that you attached to yourself when you run (in case you fall over - the belt then stops etc). i had not connected it properly

Jan 25, 2009 | Life Fitness F3 Folding Treadmill with...

Not finding what you are looking for?
RTO LifeCore Fitness LC-T900HR Treadmill Logo

228 people viewed this question

Ask a Question

Usually answered in minutes!

Top RTO Exercise & Fitness Experts

Jim London
Jim London

Level 2 Expert

257 Answers

Howard
Howard

Level 2 Expert

115 Answers

Jax Planet
Jax Planet

Level 2 Expert

922 Answers

Are you a RTO Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...