Question about NEC Televison & Video

1 Answer

NEC NLT-30W PICTURE COMES ON FOR ONE SECOND THEN BLACKS OUT, COMES AND GOES AND WILL COME BACK WHENEVER YOU CHANGE CHANNEL THEN BACK TO COMPONENT CHANNEL

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • NEC Master
  • 12,061 Answers

With this symptom, it is impossible to tell what the exact "Cause" of this symptom is. The LED's do not tell us what is wrong, sometimes it may indicate the "Area" in your case it is the X board. BUT thats NOT where the "Fault is" thats just the part that is affected. These days unlike the "Old" analogue days it just isn't realistically possible to fix anything but the most basic of problems with todays sophisticated units. This is quite apart from the Safety aspect, any unit that can cause a firs or have an explosion, or both, is NOT to be treated lightly, and and the repairer, of the unit is legally responsible, another thing to think about. Also, one must have tools, a Multimeter, a soldering iron, a deslodering iron, an oscilloscope, a signal tracer, tools, and most important of all, a Service Manual, without which, there is no way to even begin to understand and fix it, and more importantly Program it, AFTER it has been fixed. As these days a TV, is a PC, a Tuner, and an HDTV Monitor, and more, all in one. in the "old" days TV"s were more, rudimentary, and built to last for 20 years, and a "Parts" supply was set aside. They usually used to fail for only a few reasons, and they while still difficult, were less difficult to repair. Electrical knowledge was transferable, and they could be and would respond to, This-is-the-symptom-This-us-the-Fix, But that no longer applies, as now, it can be a Fault on I squared Bus, or "Sensor" failure, or it simple may have "Crashed" just like a PC, It could be a Diode go bad, and that will stop the whole thing. You see, in the day, the sets were Very "Fault Tolerant" because they were Analouge, and a faulty, component, or more sometimes, the set would always diplay something usually, and when they didn't it was one of only a few things, sure there are always the horrid ones, and there are pleanty of those, but all in all it was quite easy. But with Digital Electronics, it either goes, or it doesnt, there are usualy few half measures. I mean thats the definition of logic either going or not. So it can take very little to completely paralyse a set, and generally give the only sysmptom, it can, by not working, usually No picture, or the like. So you, see the list is endless almost for any given SYMPTOM, as that is what is being seen, not the cause, as I keep going on about. Also any fault, usually involves the Power Supply, it is either the cause, the cause of the damage, or it is damaged. or ALL of them. Then after you have done the electronic repairs, you then must program the set to work, and align, and set up in general, any one of those settings missed or done wrong, back to square one. So, it is nearly always my professional opinion that one should always get a "Quote" form the manufacturers recommended service center, I cannot stress how important that last point is. It is even worth the cost of shipping. you see an authorised service agent, will have trained staff, trained on their brand, also they have first hand access to parts, original parts. This will actually save you money and ensure you can actually get it back fixed. Of course asking for a "Quote" also gives on the option of repair or replace,
Owners manual below.
www.necbs.com.au/docs/nlt-30cw_user_manual.pdf

Posted on Jul 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My nec TV(nlt 40hl2) won't allow me to change input to pc???


If you wish to get some details; check the site linked here. Pull up older posts..........
http://electro-medical.blogspot.com/

May 14, 2016 | NEC Televison & Video

1 Answer

How to retune a tv


Whether you have a remote or not, you'll need to access a menu screen and figure out how to use the volume buttons or channel buttons to highlight the scan for channels section and allow the TV to scan to pickup or drop channels.

It's usually somewhat self-explanatory once you've accessed the menu.

Jul 31, 2014 | NEC T.v. Wall Mount

1 Answer

Tv stuck one channel


Be sure tv is set to antenna and not cable . Do auto scan . Find this in setup menu. If this does not work check the mfc website for software update. replace the main board as last resort.

May 29, 2013 | NEC Televison & Video

1 Answer

Looking for amanual for NEC RS-32PX tv


The NEC RS-32PX is a remote control. It was included with the NLT-19HDB4 TV. Additional TVs may have come with the remote. The manual for this NLT-19HDB4 is here: http://ernie.awa.com.au/ArticleDocuments/1288/NLT-19HDB4.pdf.aspx with the remote details on page 5 (page 5 of the PDF).

I hope this helps.

Cindy Wells

Aug 01, 2011 | NEC Computers & Internet

1 Answer

Nec nlt-19hdb3 lcd tv turns on, boots ok, then powers itself off after about 15 secs


Power supply board have problems.Tries unplug,replug the tv an hour later,the tv now,will reset itself back to factory setting.The tv should work now,not than the power supply board is dead.Tries websites like Shopjimmy.com,Ebay.com to buy a refurbish power supply board for the replacement.

Oct 11, 2010 | NEC ONYX NLT-19HDB3 19 in. LCD TV

1 Answer

NEC NLT-26HD1 The picture flickers on and off when turning on (cold nights especially) but the sound is ok. And when using tv information/guide and playing games or DVD's.


the main control module has a minor problem and needs to be replaced. eventually you will notice other things start to happen like flashing or colors changing.. take it to a good repair shop...

Nov 17, 2009 | NEC NLT-26HD1 26 in. HDTV-Ready LCD TV

1 Answer

How do I connect my dvd to my tv???


connect component{red, green, blue} cables to corresponding color on back of tv or yellow, red, white cable to back or front of tv and select input on remote. May be component labeled or video 1, 2 and etc...Make sure dvd player is turned on first.

Aug 04, 2009 | Panasonic DVD-RV32 DVD Player

1 Answer

No picture no sound


Hi!

It sounds like you have a power supply problem! You will probably find some bad caps (capacitors) on the board. They will look bulged on the top an may be a little leaky (brownish stain). In addition check the ribbon that feeds the lcd controller.

Feb 19, 2009 | NEC PlasmaSync 42MP2 42 in. Television

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top NEC Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74482 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Computer Repairing
Computer Repairing

Level 3 Expert

14641 Answers

Are you a NEC Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...