Question about Stanley Utility Knife

1 Answer

How do you load a new blade?

How do you load a new blade in a Stanley Quick Change utility knife?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 313 Answers

At the back end of the knive (the curved end) press the black piece through the yellow rounded part and the yellow front and the black back will part, now slide the yellow part back to reviel the blade folder. Fit new blade then refit the yellow part on top of the black part and slide the yellow part foward to lock it back in.

Posted on Jul 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a stanley fatmax knife but it doesn't have the small yellow button to help insert a new blade. what can I do?


HI!Kindly pull the button on the end of the knife and then after you remove that you can now put the blade of your knife.

Aug 21, 2011 | Stanley Utility Knife

1 Answer

How to open stanley fatmax knife 10-778 TO CHANGE THE BLADE. thank you


How do I change the blade on the quick change/instant change knife? Warning: Blades are sharp and can cause serious injury. Be extremely careful when handling blades. Wear eye protection and dispose of used blades properly, such as wrapping in duct tape.


FULLY EXTEND THE BLADE.

Press down and forward again on the slide button until the button is in the full front of the top slot (0 through 3 in the below picture).

Note- the blade must be extended beyond the 3rd detent position. This will cause the slide button to remain in a down position, allowing the blade release button to operate.

PRESS AND HOLD THE BLADE RELEASE BUTTON ON THE FRONT SIDE OF THE KNIFE. (Step 4 in the below picture)

Note- if the blade is not fully extended beyond position 3) , the blade release button will not work.

Remove the old blade carefully.
Insert new blade.

NOW, RELEASE THE BLADE RELEASE BUTTON.
ENSURE THE BLADE IS LOCKED IN PLACE. If the blade does not retract, try carefully giving a slight tug on the blade to reseat.

Jul 13, 2011 | Stanley Fatmax Xtreme Retractable Utility...

1 Answer

Have a Stanley Fat MAx utility knife and unable to open it to load the blade


there is a little black button on the end where the blade comes out. With the blade in the out position,push in the button and pull out the blade. With button pushed insert new blade or turn the old one around to use the other end.let go of the button and you are ready to go.

Jun 26, 2011 | Stanley Utility Knife

1 Answer

Cant put the thing back together after putting in new blade !!!fat max knife


some stanley knifes require stanley blades only, or make sure the clip blade is in is seated in the grove completely.

Dec 23, 2010 | Stanley Fatmax Xtreme Retractable Utility...

1 Answer

How to load blades on stanley #10-788


This knife is ****. To load... you have to push the slide all the way forward. Make sure the switch is set to unlock. PINCH THE BLADE WITH YOUR FINGERS AND WIGGLE IT INTO PLACE. Then you have to use every ounce of thumb power to relock the switch.

Once you are done, the blade will still come out in 9.9 / 10 times you cut something.

Nov 08, 2010 | Stanley Utility Knife

4 Answers

Stanley 10-788 how to change blade


Push the top metal button all the way foward as if pushing the blade out to it's (farthest) 3rd setting. Then push foward and down one more time which locks the mechanism down. Push and hold the yellow side button as you insert the blade. When the blade locks in all you have to do is release the yellow button and return the top slide to it is fully retracted home. The blade is loaded

Jan 14, 2010 | Hand Tools

1 Answer

WAS ABLE TO OPEN THE STANLEY SWIVEL LOCK UTILITY KNIFE AND REMOVE DULL BLADE. NOW i CAN'T GET THE NEW BLADE IN AND CLOSE THE KNIFE PROPERLY, WHAT'S THE TRICK?


If you use the wrong brand of blades, they won't let the knife shut all the way. The notch is cut slightly differently. The same is true for the Kobalt knife I just bought at Lowes. Get the Stanley blades that are right next to the knives - they are the only ones that work.

Sorry.

If you bought the Stanley blades, then I don't know what the problem is. Sorry for that too.

Nov 20, 2009 | Stanley Swivel - Lock Fixed - Blade...

Not finding what you are looking for?
Stanley  Utility Knife  Logo

Related Topics:

884 people viewed this question

Ask a Question

Usually answered in minutes!

Top Stanley Cutter Tools Experts

Ivan
Ivan

Level 1 Expert

35 Answers

Jim Goldsmith
Jim Goldsmith

Level 3 Expert

2005 Answers

Pete Jones

Level 1 Expert

4 Answers

Are you a Stanley Cutter Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...