Question about Whirlpool LSQ9544K Top Load Washer

1 Answer

How do i replace swich on lid the one that turns washer on when you are ready to start washing

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Whirlpool Master
  • 2,605 Answers

Hello, Welcome to FixYa.

Here`s a helpful link for changing it out...

Let me know how you make out and if I can assist you further.

Thank you for choosing FixYa today. Please take a moment to rate the solution provided for you today.

Good luck,

macmarkus :)

Posted on Jul 31, 2010

Testimonial: "this vidio was very good ,thanks very much"


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a wtw5600xw0 Whirlpool washer. When I press the start button the sensing light and lid lock lights turn on. Then after a few seconds the lid lock light goes off and the sensing light stays...

Swich off the machine, try some WD40 on the door mechanism (on machine lock, not on the door) and open & shut for a minute or two. Then try the machine, spin only just to try.

Rate pl, if solved, or dont!


Nov 27, 2012 | Whirlpool WTW5600X Washer

2 Answers

Machine won't start, lights are all on and ready to wash


If your washer doesn't seem to work at all, check these:

No power
Lid switch
No power Check to see whether power is getting to the washing machine. Is it plugged in? Has a fuse blown or is a circuit breaker tripped?

Lid switch If the lid switch is defective, your washer can't spin and may not function at all. The switch is inside the washing machine main housing near the door frame. Often you have to raise or open the top or front of the washer to get to the switch. If it's defective, you need to replace it.

Some machines have a special lid-switch fuse near the lid switch, inside the control panel. If this fuse blows, the unit won't fill with water until you replace the fuse.

Jun 06, 2008 | LG WM-1832C Front Load Washer

1 Answer

Machine not spinning

where lids closes on top of washer is a little hole. on bottom of lid is a peg that goes into that hole. try first pushing lid down hard to see if makes contact, if not that switch if does not make a click sound when depressing, most likely is out, can easily be replaced, and can do yourself. swich is maybe 20 bucks, that swich is a safety switch, to not allow washer to spin unless lid is closed, to prevent injury to a child sticking hand in when spinning.

May 11, 2011 | Fisher and Paykel Washing Machines

1 Answer

Washer worked fine all week. Today. I went to use it and I pulled the knob out to start the machine and nothing happened. Just the little red light came on. It is a Maytag top loading model LAT9734AAE

door switch look where lid closes and depresses closed swich that swich has 2 wires on it un plugg them tape them together hit start it should work

Jan 24, 2011 | Maytag Washing Machines

1 Answer

Fills with water but won't start; says not filled

have u checked the lid switch?
here is how to check that, go to link for how to instructions on lid swich.

Jun 13, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

My Kenmore 26962 Washer will start its cycle once

check you lid switch
most machines will not go into the cycle
if that switch is bad
some models have a tab on the lid that dresses this swich when you close the door
but with out the proper model number i cannot help you more sorry

Oct 09, 2009 | Washing Machines

Not finding what you are looking for?
Whirlpool LSQ9544K Top Load Washer Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Sal De

Level 3 Expert

2699 Answers


Level 3 Expert

81400 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides