Question about Life Fitness 9100 Next Generation Remanufactured Treadmill

1 Answer

Err 1 on fitness club threadmill

I get err 1 on my threadmill when it is started and the does not move, but it s on.

What do I do or how do I solve this problem

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 218 Answers

You will need to check the speed sensor for proper alignment and function. it should be located near the front roller or mounted on the motor. It should be within a credit cards width of the magnet or toothed wheel. If properly adjusted check with an ammeter to see if it is opening and closing by manually spinning the front roller or motor flywheel. If it isn't replace the sensor. If it is functioning make sure you are getting 5vdc to it across the wires. If you are not replace the upper control board(console). If you are getting the proper voltage then replace the lower control board(motor controller).

Posted on Aug 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error message E02 on Reebok ZR8 Threadmill - please help if possible


If you wish to get some details about treadmill error codes ; check the site linked here. Pull up older posts.
http://electro-medical.blogspot.com/

Dec 01, 2016 | Exercise & Fitness

1 Answer

Threadmill does not always start


There would be some problem in wiring harness between motor control board and control panel. Try to remove form both side an reconnect it
If you wish to get some details; check the site linked here. Pull up older posts.
http://electro-medical.blogspot.com/

Sep 10, 2016 | FreeMotion Xtr 90 Treadmill By Free Motion

1 Answer

How do I adjust the belt on my TX40sportcraft threadmill


Set the speed on the treadmill at 2 MPH, If the
walking belt has shifted to the left, use the hex
key to turn the left idler roller screw located on rear
of walking deck clockwise 1/4 of a turn; if the walking
belt has shifted to the right, turn the left idler roller
screw clockwise 1/4 of a turn. Be careful not to
overtighten the walking belt. Always wait to see if the
belt moves as your turning the screws. Take your time
in adjusting belt.

Mar 02, 2015 | Exercise & Fitness

1 Answer

I have different issues with threadmill


Sounds to me like the motor has a shorted field coil or open or shorted armature. The motor is bad, you can order a new one at the companies website.

Jun 09, 2014 | Nordic Track NordicTrack A2550 Treadmill

1 Answer

I have a proform 650 v threadmil, and the left side of the buttons panel (start button and incline levels) don't work. could someone help me?


1) tight all connector wires and clean
2) tight the ribbon cables from keypads.
3) Run the software calibration for diagnose, and troubleshooting, and fix it.
4) lube the shaft and gear in the elevation motor,
5) adjust the potentiometer for better running see the diagram.
God bless you

6_19_2012_4_07_05_pm.gif6_19_2012_4_07_44_pm.jpg

Jun 19, 2012 | Proform Exercise & Fitness

1 Answer

`convert threadmill from kilometer to miles on a freespirit threadmill


Dear Sir:
Inspect the bottom of your treadmill console.

Use the pencil point. touch the hole(nano swithc) and ready. Of course you must disconnect the power before. After you reconnect it. And ready.

sincerely. God bless you.

ernesto cuadra
managua, nicaragua. c.a.

Feb 13, 2012 | Bowflex Exercise & Fitness

1 Answer

V-fit treadmill belt wont turn


call the threadmill cops. they will come and beat up that error

Jun 24, 2009 | Exercise & Fitness

2 Answers

Proform 860 QT doesnt have power


There's a little breaker near the main on/off switch that has tripped. Re-set the breaker. (also check the main on/off switch, typically near where the power cord enters the treadmill...

Mar 13, 2009 | Exercise & Fitness

Not finding what you are looking for?
Life Fitness 9100 Next Generation Remanufactured Treadmill Logo

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Life Fitness Exercise & Fitness Experts

Howard
Howard

Level 2 Expert

115 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Matt Olenzek
Matt Olenzek

Level 2 Expert

293 Answers

Are you a Life Fitness Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...