Question about Maytag Dishwashers

1 Answer

Dishwasher is giving E1 which according to the manual is water sorce is off. We recently had turned the water off for bathroom repairs but the water has been turned back on, we have disconnected the pipes to run the water through, this is happening but as soon as reconnected to the dishwasher it doesnt work

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 949 Answers

Hi,

This is common, there may be a flood protection device that tripped in the line or sediment got into the system when the water was turned back on.

First turn the water off to the dishwasher. Take the hose or pipe off at the connection under the dishwasher, put a pan or towels under that open pipe. Slowly turn the water on and flush that line until clear. If no water comes out then you will need to do this but further back 'upstream'.

Once water comes clear, turn the valve off again reconnect the pipe/hose to the dishwasher and very slowly open the valve. If the water does not enter now you have sediment in the water inlet valve on the dishwasher itself and that valve will need replaced.

Posted on Jul 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My LG dishwasher when I turn it on it drains the water, then it fills it up with water, about 1 min. later gives me the code E1 and drains the water again...


LG Dishwasher Displaying Fault Code E1 LDF7810BB/01 LEAKAGE ERROR // Excessive pump motor RPM due to water leakage
The manufacturer has assigned this error or fault code to indicate that when the drain pump is running it is not experiencing the back pressure it expects. This is usually an indication that there is a water leak in the drain system. Check all hoses and connections. Check under the dishwasher for any major leak. If all checks out, be certain there is a proper loop in the drain hose to prevent siphoning. Finally, if the problem persists, the drain pump itself might be defective.
LG Dishwasher Displaying Fault Code E1

Sep 25, 2015 | LG Dishwashers

1 Answer

E1 error on Baumatic BAD6003


If you are getting E1 error then the dishwasher is suggesting that water is getting in but not enough. But if you are getting no water into the dishwasher then the water inlet valve inside it is faulty. Have you checked if there is water inside the dishwasher when you get E1 error. Another thing to find out is the water pressure specification of dishwasher and whether it is consistent with the mains pressure in the house. Usually there should be a plate on dishwasher door which would give water pressure required.

Apr 20, 2014 | Baumatic Dishwashers

1 Answer

Machine LD2131WH was in 5 cm of water but now water problem solved however machine keep giving code E1 even when taken of the mains for more than 30 minutes


Hi jwvdbok,

You are receiving the E1 error because the Circulation Motor is faulty. Please check my Tip below on how to repair it:

L.G DISHWASHER E1 ERROR

Kind Regards

JEDEMEYER1

* If you found this solution helpful, please rate it.

Jul 10, 2011 | Dishwashers

2 Answers

I have an LG dishwasher, Model LD-2120WH and lately it starts" -- water goes in but it throws up a E1 message on the display screen, send off an alarm and stops


I've just solved the same problem on my 2120. It started when the pump motor bearing failed and continued after I'd replaced the bearing. According to my handbook the E1 fault is theoretically a water leak but practically it is that the pump is not delivering enough water. In this case the failed bearing had allowed the shaft to wobble about and damage either the rotor or the inside of the pump (it's sealed so you can't strip it). Solution was to replace the pump.

Paul H

Nov 08, 2010 | LG Dishwashers

3 Answers

Lamona dishwasher from Howdens. E1 code


we have a howdens dishwasher model number hja8630, which is full of water which hasnt drained . i have ladled it out checked filters are unblocked but it still fails to start. it does a click click sound and then nothing . only 18 months old and only ever used twice a week

Feb 21, 2010 | Dishwashers

1 Answer

E1 error on LG - LD-4120M


E1 is a common error in the LG Dishwasher range and is usually caused by the failure of the circulation pump and/or the impeller.

The motor and impeller are a complete unit.

Often what happens is the impeller breaks on the motor shaft and doesn't spin, therefore doesn't pump water.

There is a pressure sensor which indicates the lack of pressure and shuts the machine down with the E1 error being displayed.

The lack of pressure can also be from a water leak (as the owners manual suggests) also a controller PCB fault may produce an E1 error, however, the pump problem is extremely common.

Unfortunately, I have had 5 pumps die in 4 years and my dishwasher is only used about 4 times a week.

Dec 23, 2007 | LG 24 in. LD-12BW5 Free-standing...

2 Answers

Hoover dishwasher error codes


Hi we have a Hoover DT999 and according to the manual for that machine error E1 is water inlet tap turned off

Dec 18, 2007 | Dishwashers

1 Answer

E1 Error on LG Dishwasher (LD-2040WH)


Maybe the blockage is somewhere else. How about removing all the trays from the dishwasher, in other words, empty it from all racks and dishes and try it again

Oct 14, 2007 | Whirlpool 24 in. DU940QWD Built-in...

2 Answers

LG Dishwasher


according to the manual that i have just downloaded from the net,E1 code means.water leakage in Hose connections.

.water is leaked by damages

hope this helps,

keith

Sep 20, 2007 | Dishwashers

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Charles T Nevin
Charles T Nevin

Level 3 Expert

4070 Answers

Mike

Level 3 Expert

4340 Answers

Are you a Maytag Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...