Question about Zonet ZSR1134WE Wireless Router

1 Answer

I went to my uncles house for the weekend & he switched the default programs or something . I can't connect to my default network anymore . It says the settings saves on my computer don't match the requirements for the network . please help me if possible

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 48 Answers

You'll have to remove the network from your sharing centre and manually add it again. You should be able to find the code on the bottom of the router.

Posted on Jul 29, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to write this problem in code

const feet_per_mile = 5280
distance = 8.5
print "the distance is "+distance "+miles or+" distance*feet_per_mile+" feet."

Jul 14, 2014 | Computers & Internet

1 Answer

My uncle gave me his 1996 lincoln continental, it has been religiously maintained up til 3 years ago when he parked it. It had gotten my aunt stranded a couple of times so they just went and bought a new...

The security system has disabled the starter. I had this happen on an earlier model Honda Civic. As a solution, we bypassed the starter and added a push-button switch on the inside of the car. So you'd turn the key to start, hit the button, and it started. We took a bit and drilled a hole in the lower dash for the button to fit, some place easily reach by the driver. From the switch we ran 2 wires, one to the ignotion wire, that we pulled off the starter, and the other to the + side of the battery.

This was the cheapest route. I had attempted to remove the security system, but to no avail.

If you're looking for a professional fix...I'm sorry I don't really have one.

Hope this helps.

May 10, 2011 | Lincoln Continental Cars & Trucks

2 Answers

We have reformated our laptop but it seems my uncle did not reconfigure the settings for our wi-fi how do i do that??

See the router manual how to reset the wi-fi password. Assuming you don't have the manual anymore, here's the defaul password list:
First connect to the router using rj45 cable. Type ipconfig to the command prompt and see the line Default Gateway. Type the number with (amount of numbers may wary) to your web browser. It asks you for your password, If you haven't changed this you can find it from the list above. Now go tho wlan section and retype the pre-shared key/password.
If you don't remember the password for the setup, you can press the reset button in the back of the devise for more than 10 seconds and all should be set to default and after that do the above again.

May 03, 2011 | HP Computers & Internet

1 Answer

My Acer Aspire 3000 does not recognize my wireless network anymore. It says it cannot find any networks - I verified that the network is ok. The device manager says the device is working properly. I went...

Check in the bottom right hand corner for another program that might be accessing the wireless hardware. Belkin (for example) often have their own connecting software that conflicts with the windows version.

Jul 25, 2010 | Acer Aspire 3000 Notebook

1 Answer

Belkin54g default gateway problems and connecting to router page

reset your Router via pin whole at its back then set the config of TCP/4 and obtain Ip automaticaly and obtain DNS automaticaly... later set your settings according by without changing IP and then turn off you router ... turn it on after 5 to 10 min .. thank you

Jun 24, 2009 | Gateway Belkin 54g Wireless DSL/Cable...

1 Answer

Defualt gateway problems with belkin54g cannot connect

1. Click Start, click Control Panel, click Network and Internet Connections, and then click Network Connections.
2. Right-click the network connection that you want to configure, and then click Properties.
3. On the General tab (for a local area connection), or the Networking tab (for all other connections), click Internet Protocol (TCP/IP), and then click Properties.
  1. Check the option which says use the following ip address and enter the ip address that you have forced in the belkin router, type the subnet mask and enter the default gate way the ip address of the belkin router (ip address that you use to open Belkins page)

Jun 23, 2009 | Gateway Belkin 54g Wireless DSL/Cable...

1 Answer

Truck only drives in 4x4

i think there is something in the transfer case causing it probably an acutator

Nov 17, 2008 | 1986 Chevrolet K2500

1 Answer

Keeps dropping the Wireless network

If you have 2.4 GHz phone in your house, it might interfere with your wireless network. Switch all your cordless phones to 5.8 or higher.


Feb 29, 2008 | D-Link AirPlus G DWL-G122 802.11g/b...

1 Answer

Xbox 360 won't turn on

he should first switch his xbox 360 before his uncle check the electricity power source in the house.

Dec 24, 2007 | Microsoft Xbox 360 Console

Not finding what you are looking for?
Zonet ZSR1134WE Wireless Router Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zonet Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2264 Answers


Level 3 Expert

4354 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Are you a Zonet Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides