Question about AEG Washing Machines

Open Question

AEG 86700 error code C8 Doesn't do final spin and then can't open door

Posted by on

4 Suggested Answers

aborcass
  • 2651 Answers

SOURCE: No final spin- washer tub rocks back and forth and times out

e47 i believe is a door lock issue, although its locking shut there are multiple switches in the lock mechanism

Posted on Feb 23, 2008

  • 1 Answer

SOURCE: CA Error Code - AEG OKO LAVAMAT 86700

c-a error message poped-up.washer stop working.............please help.

Posted on Nov 18, 2008

  • 1 Answer

SOURCE: AEG OKO_LAVAMAT 74620 gave me a code error C7. What is it?

take off the bottom front panel, a booklet is taped to the right side of the panel for the sevice tech it has all the codes

Posted on Feb 28, 2009

  • 9 Answers

SOURCE: he 3t error code f6,washer will not spin,door will not open

"f6" error code means that there a miss communication between mcu(motor speed control board) and ccu(central control unit). i recommend you to ohm out the motor. most likely its your motor speed control located at the bottom left of the washer good luck. replace the motor speed control board and you should be all set to go.

Posted on May 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My citrion c8 boot is locked. The side door have to opened and shut manually. The passenger door doesn't lock when locking drivers side. The hone doesn't work. Please can anyone help?


sounds like a fuse, check EVERY fuse before ruling it out as the problem. anything else is going to the garage and they will charge you if it ends up being a fuse

Jul 13, 2013 | Cars & Trucks

1 Answer

Can't open door


the two possibles are faulty door lock or water still in the machine. the error code should tell you which. go to AEG and their troubleshooting page will give you the codes.

Jan 30, 2013 | AEG Lavamat 72640 Front Load Washer

1 Answer

Aeg W1039 will not spin


It is possible that the machine does not start off the cycle because there are errors due to feedback from the inputs. For the program to start up the main program controller must initiate the INLET/MOTOR/DRAIN pump/ valve to open up and allow each function to be driven starting from the flow of water into the drum as also the drain valve to open to exit the water at the point of the program cycle. If this does not happen then the voltage at the valve/motor/pump must be checked or the fault relates to no voltage from the controller. This means the controller is a suspect.

Once the water comes into the system the WATER LEVEL SENSOR - normally a pressure switch- must activate at the preset/chosen level to give the signal to the program controller to switch on the motor. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor for rinse and wash.

Finally after the wash the drain valve will be activated, the water is allowed to come in to rinse and then finally the dry spin with the drain valve/pump activated so as to drain off all the water from the clothes during the spin.

Make sure that a fault in any of the cycle will relate to the specified action, so check the command from the program module and then the executing device be it the valve or motor or pump.

Please check the link below:

http://www.repairclinic.com/Washing-Machine-Troubleshooting?red=Washing-Machine-Repair-Help

Thank you for using fixya.

Sep 23, 2011 | AEG Washing Machines

1 Answer

I have a AEG 74620 lavamat washing machine and the error code C2 is appearing. The load wont finish. Any idea what the issue is?


It is possible that the machine does not start off the cycle because there are errors or back feedback from the inputs. For the program to start up the main program controller must initiate the INLET valve to open up and allow water to flow into. If this does not happen then the voltage at the inlet valve must be checked or the fault relates to no voltage from the controller. This means the controller is a suspect.

If the water flows then the flow should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. Once the water comes into the system the WATER LEVEL SENSOR - normally a pressure switch- must activate at the preset/chosen level to give the signal to the program controller to switch on the motor. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor for rinse and wash.

Finally after the wash the drain valve will be activated, the water is allowed to come in to rinse and then finally the dry spin with the drain valve/pump activated so as to drain off all the water from the clothes during the spin.

Make sure that a fault in any of the cycle will relate to the specified action, so check the command from the program module and then the executing device be it the valve or motor or pump.

Please check the link below:

http://www.repairclinic.com/Washing-Machine-Troubleshooting?red=Washing-Machine-Repair-Help

Jul 13, 2011 | AEG Washing Machines

1 Answer

Aeg oko lavamat 6555 cannot open door no response to buttons F9 flashing


Hi


Error code F9 means an error with motor or motor tacho failure. Try resetting the error by pressing quick and prewashing buttons together while turning the knob to gentle spin. All LED's will glow, now turn the knob back to Off and the machine should work. Hope this helps... Please post back for any further assistance.


Daniel

Aug 29, 2010 | Washing Machines

1 Answer

What does fault code c8 mean on an AEG Lavamat 76669


a C8 warning means the (Thermister) temperature sensing device has shorted or is open circuit, this replaces the old-fashioned thermostat that they used to fit. the water in your m/c could either stay cold or boil.

Jul 07, 2009 | Washing Machines

1 Answer

AEG OKO_LAVAMAT 74620 gave me a code error C7. What is it?


take off the bottom front panel, a booklet is taped to the right side of the panel for the sevice tech it has all the codes

Feb 28, 2009 | AEG Lavamat 72640 Front Load Washer

1 Answer

CA Error Code - AEG OKO LAVAMAT 86700


c-a error message poped-up.washer stop working.............please help.

Sep 15, 2008 | Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

AEG Oko Lavamat 86700


check the carbon brushes on the motor as when they are worn arcing occurs and this could trip the electric and the smell could be the plastic brush holders getting hot due to the arcing

Jul 15, 2008 | Washing Machines

3 Answers

Door not unlocking


open the filter door at bottom turn screw with coin , door should open ,

Oct 02, 2006 | AEG Lavamat Lavalogic 1600 Front Load...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top AEG Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you an AEG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...