Question about Altec Lansing VS2121 Computer Speakers

1 Answer

WIRING DIAGRAM HI IS THERE SOMEONE OUT THERE WHO COULD POSSIBLY HELP ME MY BROTHER TWEAKED ON MY CABLE AND CUT OFF ALL THE WIRES CONNECTED TO THE PINS PLEASE I NEED A DIAGRAM SHOWING WHICH CABLES CONNECT TO WHAT PIN

Posted by on

  • Anonymous Dec 23, 2008

    My rabbit ate through the 7 pin mini din connector wire. What type of cable can I get to fix it?

×

1 Answer

Yo have wiring diagram :)

send your e-mail address to southener83@hotmail.com

Posted on May 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My radio sound just stopped working, everything else was fine so I've come to check my connections and the one of the ISO plugs which controls the speakers is faulty but I don't know what side.. The pins...


If it were mine, I would just crimp the wires together and do away with the plug altogether. You could try using some lithium grease but that probably won't do much good. Go with the crimps. A cheap crimping set with crimps and tools are easy to find at $10 or less. Just crimp the wires as they are connected at the plug.

Feb 26, 2015 | Computer Speakers

1 Answer

Creative 9 pin male din damaged


The only way to go is Replace the 9 pin adapter. Radio Shack may have the adapter, check them out. You will need to be observant when locating the proper colored wire corresponding with each pin. Two ways to do this and all require a soldering iron. Either split or open the cover on the 9 pin male adapter and expose the wires going to each pin. Identify the colors and pin numbers and draw a diagram on paper to keep for reattaching the wires later on. Cut 1/4 of the insulation back from the end of each wire and tin the wires. In short, hold the solder to the wire ends and heat with the iron so a flow of solder runs along the bare wire. Make certain to put a connector cover onto the wires prior to soldering each wire in place on the pin end. Simply set the correct colored wire end in the proper pin number, hold the iron to the pin back end and allow the wire to affix itself. Do this with all wires. If you do not have 9 wires, that is not unusual, just do the procedure with what wires are available. If you cannot get the outer jacket off of the current 9 pin connecter, then you will need a Volt/Amp meter. Here you simply cut the wire approximately 1/2 to 2/4 Inch back from the cable 9 pin adapter, and locate the pin that corresponds to the colored wire. Using the RESISTANCE part of a meter, when you touch the two probes together the needle moves on the scale. Touch one end to a pin and try each colored wire end until you see the movement on the scale. Now you know what color corresponds with each pin. Solder each colored wire as mentioned above.

Dec 15, 2013 | Creative Technology SBS A200 2 Speakers

2 Answers

9 pin diagram altec lansing


can anyone help me with the Altec Lansing VS4121 2.1 Channel i need the wiring diagram of 9 pin cable i broke it. please mail me the layout at maurya.mohit07@gmail.com

May 20, 2012 | Altec Lansing VS4121 2.1 Channel Powered...

1 Answer

RCA jack in back of the speaker is no longer connected. I can NOT get the cover off the speaker.


cut connectors from board & join cable of speaker & output wires

raj@npconline.in

Jan 26, 2011 | Klipsch ProMedia GMX D51 5 Speakers

2 Answers

How can i repair or replace the audio cable


You can go to radio shack and buy a replacement plug end and splice it into your cable.

It will require a little soldering to secure it but it should work fine when your done.

Good luck and be careful.

Feb 17, 2010 | Harman Kardon SoundSticks II Computer...

1 Answer

I wont to connect my computer audio system to my tv but it has green/orange/black wires amd my tv has only one headphone jack. what do i do?


in ur computer there are three pins audio,video,cable namely u connect ur audiopin that is orange in colour connect to tv and the chargerc is connected to ur plug holder. sir please rate me dont forgot to rate

Jul 11, 2009 | Logitech X-530 Computer Speakers

2 Answers

Brother tripped over cord connected to laptop


Sounds like the wires inside got pulled loose or broke. Replace the speaker wires or check them good for connection.
I can't fix this for you, but if I helped you get it fixed, please rate it as a fixya not a helpful rating. These ratings let me be allowed to help you and others in the future.

Jun 02, 2008 | Logitech Z-2300 2.1 Computer Speaker...

1 Answer

Broken D-sub cable


I would advise against a direct solder inside the unit. I would go and purchase a replacement connector from a Radio Shack or other electronics parts store. Solder wires to this, then plug in, should fix problem.

Apr 03, 2008 | Logitech Z-2300 Computer Speakers

3 Answers

VS-2121 altec Lansing - ORANGE BIG FAT CABLE MISSING TWO MIDDLE PINS


well u could try a shop that sells music equipment they should be very common... but u need to know how to solder :D or at www.aswo.com i think they have cables....

Jan 19, 2008 | Altec Lansing VS2121 Computer Speakers

2 Answers

My conrol cord has its pins distorted


Well Friend,

What is the brand , name, model of your mobo, and what "control" is what you talk about.

Nov 25, 2007 | Altec Lansing ATP 3W Computer Speakers

Not finding what you are looking for?
Altec Lansing VS2121 Computer Speakers Logo

Related Topics:

1,635 people viewed this question

Ask a Question

Usually answered in minutes!

Top Altec Lansing Computer Speakers Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Carlos L. Burgos
Carlos L. Burgos

Level 2 Expert

508 Answers

The Knight
The Knight

Level 3 Expert

68352 Answers

Are you an Altec Lansing Computer Speaker Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...