Question about Whirlpool GEW9200L Electric Dryer

1 Answer

E-1 CODE TURN IT ON GET E-1 CODE TURN OFF AND BACK ON SOMETIMES IT CLEARS

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Whirlpool Master
  • 3,051 Answers

Hello there
This code can sometimes be the e-1 or sometimes the e-2 here is the descrioption of what it means
E1 or E2 Thermistor Failure The dryer will not operate if the exhaust temperature drops below 18 degrees F. or exceeds 250 degrees F.

When the thermistor circuit is open (>50K ohms), the error code E1 flashes in the display.

When the thermistor circuit is shorted (<500 ohms), the error code E2 flashes in the display.

Normal thermistor resistance values:
60 degrees F. - 15.3K ohms.
70 degrees F. - 11.9K ohms.
80 degrees F. - 9.2K ohms.Dryer thermistor assembly
E-1 CODE - f2e3f51.jpg

Posted on Jul 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whats the difference between a current code and a pending code?


Pending codes and current codes are basically the same. Pending codes are for a problem that is still indicated to be a problem,but hasn't been cleared. Current codes are codes that are indicated for the current drive cycle. Usually will both be the same code if problem still exists and hasn't been cleared without repair.

May 12, 2014 | Cars & Trucks

1 Answer

Need the stereo reset code for a 1994 bmw k1100lt


Turn off the ignition. Hold down the ST button and turn the ignition back on. Keep holding the button until the display clears. Now enter the correct code.

Sep 08, 2011 | BMW K 1100 LT Motorcycles

1 Answer

Iv'e been trying to turn my tv on for an hour but the led light just keeps flashing why won't it turn on?


The flashing light is a service code for a technician to let him know there is trouble with the set. Most common issue on these is the power supply or one or more of the circuit boards. You can try a reset by unplugging the set and let it sit for an hour or so, preferably overnight then plug it back in this sometimes clears codes and then it can resume.

Apr 08, 2011 | Sharp Televison & Video

1 Answer

Our Sony tv lost picture then shuts off and a red light keeps blinking


Ther are no resets the blinking light is the code for the tech to diagnose the issue. Most likely you have lost a circuit board, the most common is the power supply. There are a lot of bad capacitors in these sets and when they die they take the tv with them. Check your manual for the trouble shooting and see if you can tell by the blinking pattern of the lights what the issue might be. The other only hope is to unplug the set for at least an hour and then plug back in and turn on. This sometimes clears a bad code or reading. If not then the set needs service.

Apr 04, 2011 | Sony Televison & Video

1 Answer

I keep getting an error code( Er IF) on my kenmore refrigerator(#79578412800) . So far if I turn off the icemaker for a day or two the error will go away and I can turn the icemaker back on it will work...


I have the same problem as JJ1764... I keep getting the same error code ER IF and all the ice melted and water was everywhere... If I turn off the fridge and then turn again it clears for a few minutes but then goes back to the same thing...Why is this happening?

Feb 20, 2010 | Kenmore Refrigerators

1 Answer

T5 error code (Model MDG9700AWW )


turn power off to the dryer for a few sec and turn it back on and see if it clears

Aug 24, 2009 | Maytag Dryers

1 Answer

Fisher tv monitor intermittently turns to snow and loud buzzing


Could it be vertical IC loose connection. It is sometimes connected with correct tuning. Check it for crack or wiggling connection best is to resolder.


Feb 02, 2009 | RCA Alert Guard 20" Flat Screen 20F670T...

1 Answer

Smoking Kenmore


Hello oliver909
Welcome,

You said,Smoke is coming out of the back of my gas Kenmore oven. Oven is clean - no spills/debris. Ran clean cycle and broiler did not smoke. Warmer drawer at bottom, so nothing spilled there. Soon as you turn it on, downstairs is full of smoke. Sometimes after preheat goes off, smoke clears and its fine. But I'm afraid to use it because last time I saw a flame inside.

If your afraid to use it, do not hesitate to call service. Nobody wants a fire!
Huuum

Oct 09, 2008 | Kenmore 33464 / 33465 / 33469 Gas Single...

Not finding what you are looking for?
Whirlpool GEW9200L Electric Dryer Logo

Related Topics:

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Sal DeAngelo

Level 3 Expert

2183 Answers

Are you a Whirlpool Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...