Question about Technics SA-DA10 Receiver

1 Answer

Speakeres killer don``t now whu,but my SA-DA 10 have allready destroed 4 par speakers,KEF Q-50,DALI EAGLE,TECHNICS,AND ONE MORE.Everytime,the hightoner dies...weard,is it?now i got wery exspensive whafendale speakers,but i``m afreid to even conect them.PLEASE,HELP....I WONT TO LISTEN MY MUSIC AGEIN.THANKS SANY K?BENHAVEN

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Technics Master
  • 5,568 Answers

Are you paying attention to the power rating of your speakers? Your receiver has a high power capability and would be quite capable of destroying speakers with inadequate power handling capabilities.

By the way, the Tivoli was a great place to be in 1963 for a young guy!
Hope it still is . . .

Posted on Apr 23, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Safe to use 4 speaker with Technics Receiver?


The best thing to do is place a VOM meter to confirm that there are 6 ohm speakers

Nov 21, 2014 | Technics Audio Players & Recorders

1 Answer

Speaker hookup for sa gx690 technics


http://www.hifiengine.com/manuals/technics/sa-gx690.shtml

Register for free and download the manual. It's pretty straightforward and everything is marked.

Jul 14, 2011 | Technics SA-DX940

1 Answer

I moved and cannot find manuel for sa-dx940 need instruction on how to reconnet wire to t.v. and speaker


The Technics SA-DX940 is made by Panasonic. The manua as a PDF is available here: http://service.us.panasonic.com/OPERMANPDF/SADX940.PDF . The directions for connecting the speakers start on page 14. The connection to the TV is on page 10. To use the SA-DX940 as just external speakers for your TV, connect either the digital audio out from the TV (if it has one) or the RCA audio out from the TV to the matching TV audio in on the SA-DX940.

I hope this helps.

Cindy Wells

Jun 30, 2011 | Technics SA-DX930 Receiver

1 Answer

OVERLOAD


First of all the KEF is a powered sub which means that it wants a line level signal NOT a speaker level. Send the signal from a tape output or pre-amp output to the sub input. The overload is because the impedence load for the speaker output is too low and looks like a short to the amp. Continued attempts to connect the system as described will result in damage to the output section of the amp.

Please let me know if you need more info.

Dan

Feb 03, 2010 | Technics SA-DX750 Receiver

2 Answers

My Technics AV Control Receiver SA AX530 is in overload


An amplifier should never be turn on without speakers, it will overload internally.
make sure speakers work and try again.

Dec 04, 2009 | Technics SA-AX530 Receiver

2 Answers

Technics sa 400 Receiver


check inside to see if you have a blown fuse on the left channel

May 27, 2009 | Technics Audio Players & Recorders

1 Answer

Max. wattage for speakers w/ Technics Receiver SA-GX100?


I too have a Technics SA-GX100 and it's rated at 2 x 40W @ 8 Ohms. I have the Technics SB-2840 floor model speakers hooked to it, which are rated at 200W Music Input - 8 ohms. It sounds very nice just to be a 40W receiver.

Apr 06, 2009 | Technics SA-AX720 Receiver

1 Answer

I have a technics amp that has hf lf speaker output I'm trying to connect them to speakers with only 2 wire red black


pa ti si car ... izgubio si se sa dve zice ... prijarelju uzmi nesto bezicno ili nikada neces slusati muziku. Gde ima tri zice ... mozes da umres ... cuvaj se. Pozz

Sep 09, 2008 | Technics Audio Players & Recorders

1 Answer

Speakers killer


I don't have the specs available for your SA-DA10 so the distribution of power over frequency is unknown to me but the receiver is capable of ~500 watts with most of it likely concentrated in the lower frequencies which do require more power to produce.

However, if your speakers are all of the typical wire-wound voice coil construction, the tweeters and midrange speakers use a much finer gauge of wire that has less power handling capability than the heavier stuff used in woofers.
That is lighter wire is necessary to keep the moving mass of the speakers low otherwise they would not be able to move quickly enough to reproduce the higher frequencies.

Additionally, it is possible (I have seen it) that your amplifier section is producing output frequencies caused by internal oscillations (a defect) that were not part of the sound they were trying to reproduce. These unwanted sounds can be well above the range of hearing so would only serve to destroy the speakers.

This problem could only be caught by an oscilloscope, not seen by the average analog or digital meter.

There is also a chance that you have DC offset voltage on the guilty channel; something that could be seen with an inexpensive multimeter; if you don't own one, there are incredibly cheap but adequate Chinese meters (digital type) that can be had for a few dollars in the US (as little as $3 US) and are probably available in Denmark too.
I suggest you should have one at home for many simple tests as they require very little technical knowledge to use.

I would have all speakers connected but NO SOUND being produced.
Measure ACROSS each of the speakers' output terminals (at the receiver or the speakers) and look for any larger DC differences between the several channels.
There should be very low levels of DC voltage (less than a volt) at those points regardless of how long the receiver has been on.

There seem to be many reports of failed output modules (discussed elsewhere at Fixya) and this could easily cause especially the high frequency speakers to fail from static (no sound) current flowing through them.

The Tivoli has apparently grown since I last saw it (~ 1963-4). When I knew it, it had several dance halls, many places to eat and a great number of very friendly English-speaking young women, the latter was much appreciated by myself and other Americans of my age.
I am afraid my traveling days are gone so enjoy it for me when you next go there!

Steve

Apr 24, 2008 | Technics SA-DA10 Receiver

2 Answers

SA DA -10


If all the speakers are connected proper and it still says "Overload!!!!!"

Your output amplifier module is most likely failed.

Mar 08, 2008 | Technics SA-DA10 Receiver

Not finding what you are looking for?
Technics SA-DA10 Receiver Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Technics Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

4678 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

T-Comtech Repairs
T-Comtech Repairs

Level 2 Expert

417 Answers

Are you a Technics Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...