Question about Washing Machines

1 Answer

Belt-drive for Bosch WFD2060GB/01 - Washing Machines

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 101 Answers

What is your question?

Posted on Apr 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, Can someone kindly assist with operational manual for Bosch washing metchen WFR 2850/01,and how to change the launguage


this link will take you to the Bosch home page you'll find a full user manual for your machine there http://www.bosch-home.co.uk/customer-service/download-instruction-manuals.html

Oct 14, 2014 | Washing Machines

1 Answer

Replace the drive belt


Remove the back
hook it on the motor pully and start to wrap it around the drum pully until it is to tight to continue then turn the drum pully to finish the job

Sep 27, 2014 | Bosch Washing Machines

1 Answer

Need instructions for moving -- have four bolts!


Hi.

Here the full set of instructions for the model Bosch WFMC 3200 posted in title:

WFMC3200UC/01 Manual 1

WFMC3200UC/01 Manual 2

Here repair manual available for $9.95.

Regards.

Ginko

Jun 07, 2011 | Bosch WFMC 3200 Front Load Washer

1 Answer

Machine worked fine last night. This morning spin not working. Have tested it empty, put it in spin program, a funny clicking noise and then nothing, then after a while indicator shows 01 - ie. finished!...


n most washers the F01 error indicates an control board problem. It is like an internal program error.

A power glitch can cause the problem.

One of the things to try is to enter and run a diagnostic cycle, or unplug the machine for 30 mins.

Jan 24, 2011 | Bosch Classixx WFO 2866 Front Load Washer

1 Answer

Hi there, have got a bosch 1200 classixx WF02466GB/01 - pumps working but will not spin the drum. Belt is ok and drum does move when you push it.


To make sure it is not due to water left in the drum, remove the filter, and clean.
If it still does not spin, then it is more than likely that the brushes need replacing in the motor..
You will have to remove the motor to check them..
If they are less than 3 or 4 mm long, then they need changing.
Hope this helps.

Dec 22, 2009 | Bosch Washing Machines

2 Answers

My bosch classix 1200 fl wont spin or drain


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Plug off the wall first. Remove the front lower panel, screws underneath. Be prepared for water, drain out from drain hose. Check filter for clogging, clean out. Sometimes when the load is unbalanced & the machine cannot adjust the load it stops. To avoid this make sure your wash is mixed with big and small clothes.
If this does not work remove the rear panel & check belt, should have half inch ‘give’. Still not good, remove belt, unscrew 2 bolts that hold the motor, unplug the motor connector, lever the motor back with a screwdriver. Check the motor brushes (at terminal end of motor), if they are any shorter than 1 cm replace brushes.
Try these sites for spares:
RepairClinic.com
espares.co.uk
AppliancePartsPros.com

mcminone.com

Oct 15, 2009 | Bosch Classixx WFL 2066 Front Load Washer

1 Answer

Bosch 1200 classixx not spinning


bosch 1200 classixx not working properly. On 12 min spin cycle it starts then after 1 min timer reads 0:01 and it stops. washing cycles run but doesn't seem to be any spin action

Oct 12, 2009 | Bosch Washing Machines

1 Answer

Our brand new bosch exxcel washing machine is jumping all over the place. We have checked it with a spirit level and it is level. The feet are tight. The washing is loaded level. What is wrong ?


hi The drive belt (or belts) of a washing machine may become worn or damaged, causing noisy operation or stopping the washer entirely. A damaged drive belt is easy to replace. Remove the back panel of the washer to gain access to the belt. 

Sep 12, 2008 | Bosch Washing Machines

1 Answer

Bosch wont spin


go back inside it and look at the place where the drive connects to the drum is there anything loose or missing that should be attached the drive coupling breaks or comes loose, i dont know about this particular model if its a belt driven or what but look closely at the connection to the drum and see if anything is abviously loose or broken.

Dec 20, 2007 | Bosch Classixx WFC 2465 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...