Question about Hoover H130E Front Load Washer

1 Answer

How can I fix my Hoover Washing Machine, model H130E?

Each time I switch on the washing machine the lights on the control panel start flashing and as a result I can't run the wash cycle. I've tried holding down the start button but that doesn't stop the buttons flashing.

Any ideas?

Thanks!!

Sarah

Posted by on

  • 3 more comments 
  • Anonymous Feb 10, 2009

    The problem started that the machine would stop as it got to the rinse cycle. Now nothing happens, all the lights are flashing on the front of the machine.

  • Anonymous Mar 14, 2014

    my hoover washing machine time saver light comes on just befor the rinseand stop.

  • Anonymous Mar 15, 2014

    the wash light flashes when I press the start button but machine won't start

  • Anonymous Mar 24, 2014

    Won't start cycle

  • Anonymous Mar 27, 2014

    LIGHTS FLASHING ON PANEL ERROR CODE F01

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 101 Answers

Which light?

Posted on Apr 23, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an Indesit washing machine. After it's been switched off and you Press power button, all light continuously flash won't even start any wash cycle


WASHER WILL NOT START:

Power If your washing machine won't start, begin by looking at the power source. First of all, is the washing machine plugged in? If it is, has it tripped a circuit breaker or blown a fuse? Check and reset the breaker (or replace the fuse) if necessary.

Lid Switch The main control for the washing machine is the switch inside the lid. If this has stopped working for some reason, your washing machine won't start. It's not especially difficult to troubleshoot this on a washing machine. You might have to open the top to access the switch. With the power on, depress the switch and listen for a click. If you don't hear one, the switch MAY BE BAD and will need to be replaced. Confirm defectiveness with a multi meter checking for continuity OHMS. An open circuit reflects a bad switch..
If the switch works but the washing machine still won't start, check to see if your washing machine has a special fuse for the lid switch. It will usually be inside the control panel. If it's blown, you'll need to replace it before the washing machine will start.

Door Interlock The problem could be with the door interlock. If the lights come on but the machine won't start, this might well be the cause. This could either be down to the wiring that runs to the door interlock, or the door catch not activating the interlock itself.

Timer Knob Some models of washing machine use a mechanical timer knob and won't run until the water in the machine has filled to the selected level. If the knob doesn't line up properly with the graphics on the control panel, you can try to troubleshoot the washing machine problem by advancing the timer a little. When you've done this, pull it out a little way and see if the washing machine will start properly.

Overheating If you've run several loads, one after another, without any problem but suddenly find your washing machine refuses to start, overheating could be the cause. The simple way to discover whether this is the problem is to give the machine ample time to cool down, say for a couple of hours, and then try it again. If it works fine, overheating has been the problem and you may have a motor with bad windings.

Apr 12, 2015 | Indesit Washing Machines

1 Answer

Washer repeats entire cycle - does not stop at end of spin cycle.


It is possible that presence of moisture within the START button can trigger the cycle to continue as it keep the processor to continue the wash cycle,Hence you must remove the panel and board after disconnecting the wiring harness and use a hair dryer to warm off any presence of moisture on the panel and board. Do it with time to ensure there is no moisture within the panel.
I think this must solve the issue. Repeat the work many times as sometimes moisture and dirt together might form a conductive bond to trigger as a pressed on switch. If possible open panel to clean switch pad.

Jan 23, 2013 | Kenmore 2.1 cu. ft. Compact Portable...

1 Answer

Lock light turns on then blinks and wont start


Possible that the lock switch contact has some issues, try a cleaning spray on the switch and open and close the door several times with the spray. This might clear the switch contacts.
Also make sure that the contacts to the connectors from the control panel are in order, remove and tighten or repeat few times.
Otherwise the control panel can be a suspect.

Jul 03, 2012 | Maytag Bravos MTW6600T Top Load Washer

1 Answer

My washing maching is reading E20 and it is not washing. it seems to stop after a few minutes of washing and then it will read E20 and just continuosly beep


Hello.

Frigidaire front-loading washing machines have an electronic control panel where the wash cycle and any other wash options are selected, and the wash cycle is initiated and stopped, if necessary. The control panel also has indicator lights that show the washer status and will display an error code if there are issues with the washer. The "E20" error code indicates a possible pump problem.

Blocked Pump

One of the primary reasons why there may be an "E20" error code on a Frigidaire front-loading washing machine is if there is something blocking the pump. Disconnect the washing machine from the power and release the clips on each side to remove the front access panel. Set a container under the pump drain, which is located on the lower right side of the washing machine. Open the pump drain plug and allow it to drain. Clean out any debris that might be causing the obstruction, then close the drain plug. Close the access panel and restore power to the washer.

Drain Hose

If the drain hose is blocked or crimped, the water may not pump out fast enough, causing the pump error to appear on the display. Straighten out the drain hose in the rear of the washing machine and move it away from the washer if it's trapped between the wall and the washing machine.

Oversudsing

If too much detergent--or the wrong kind of detergent--is used in the washing machine, too many suds may result. This can overwhelm the drain and pump system, resulting in the error. Use only high efficiency (HE) laundry detergent with Frigidaire washing machines and follow specific instructions on the laundry container for the recommended amount of detergent. Run a drain cycle if there are excess suds in the washer to clear out the system.

Pressure Switch or Control Boar

The pressure switch may not be communicating properly with the control board, which can cause the E20 error to occur. The other possibility for the E20 error code is if the control board has failed entirely. Try to reset the washing machine by pressing "Stop/Cancel" and disconnecting the washing machine power cord. Wait 30 seconds, then restore power. Make a new cycle selection and press "Start" to see if the error code returns. If it does, turn off the washing machine and contact Frigidaire for repair.

Thanks.

Nov 08, 2011 | GE Energy Star WCVH6260F Front Load Washer

1 Answer

Washer stops at the same point every time which is after it fills with water. After several hours it will then restart. Do you know what the problem might be? Thank You


Hi.

There are different faults that result in machine stopping mid cycle, hanging or not completing the cycle. Thermostat and element, pressure switch, balance switch, control module, door switch and motor must be tested. Common faults when machine stops mid cycle always at same time concern pressure switch and heating system. Some are described here (I know your machine properly stops and does not hang like the one in example): Washing machine takes a long time to end cycle.

To know what the problem is you need to run a test cycle. Instructions on how to run a test cycle are described in the tech sheet that is normally placed inside the machine. The tech sheet is usually tucked in an envelope hidden inside the control panel. It is necessary to remove the control panel held by screw to see if the document is still there. Power must be disconnected first.

Regards.

Ginko

Sep 07, 2011 | Kenmore Washing Machines

1 Answer

How do I use the Child Lock option on Samsung WF-B1456GW?


Hi there,

You can use the child lock feature in 2 ways.

1. To prevent operation of the washing machine when no wash cycle is running

To set this feature, switch the machine on using the POWER button at the top-left of the control-panel. Next, press and hold both the SPIN and RINSE buttons for about 3 seconds - until the child lock light indicator on the control panel illuminates. All functions of the washing machine will now be disabled apart from POWER ON/OFF until such time as the child lock is deactivated.

To deactivate the child lock, press and hold the SPIN and RINSE buttons again until the child lock light indicator on the control panel goes out.

2. To prevent any tiny fingers from tampering with the machine while a program is running.

After pressing the START/PAUSE button to start the wash cycle, press and hold the SPIN and RINSE buttons until the child lock light indicator illuminates. All buttons on the control panel will now be disabled until the child lock has been disabled. When the wash cycle has finished, you will need to switch the child lock off again to reactivate the buttons. Once you have finished using the washer, reactivate the child lock again before switching the power off as above.

The feature can also be used when using the delayed start feature, but needs to be set after pressing the START/PAUSE button.

Hope this helps. Please let me know if I can be of further assistance.

Regards,
BElectric

Feb 09, 2011 | Washing Machines

1 Answer

Ariston A1635 Margherita Control knob spinning


According to the instruction book - it appears the machine has been stopped mid cycle then re-started.
Switch machine off, turn control knob to a solid circle symbol (they are after every set cycle). Switch machine back on and lights will flash and program is reset. You can then select wash cycle as normal.

Jan 22, 2010 | Ariston Technologies AW125NA 13 lbs. Load...

Not finding what you are looking for?
Hoover H130E Front Load Washer Logo

691 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Chris Hall
Chris Hall

Level 3 Expert

842 Answers

shaun taylor

Level 3 Expert

1525 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...