Question about Car Speakers & Subwoofers

1 Answer

Error 3 displayed for 2005 4-runner jbl 6-disc changer.Won't eject cd's. Any solution?

Posted by on

  • jimmie53 Apr 24, 2008

    Where is the reset button located?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Turn your car on. Take a pen and press the reset button located on the disc changer. Hold for about 30 seconds and try it again.

Posted on Apr 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

MCD36 6 disc changer won't eject or play CDs. Erro messages are Surface or CD loading!


Please remove the top cover and manually rotate the motor to release the loading. It can be due to a warped cd or a motor pulley which had slipped.
Also check if the linking cord to the loading motor is having a continuity.
If not there is fault in the processor controller or the loading IC.

Aug 09, 2011 | Car Speakers & Subwoofers

1 Answer

2005 Corolla cd player "ate"


try disconnecting the battery for a few minutes to reset the radio. Sometimes a microprocessor will lock up. You can reset it by disconnecting the battery.

Jun 01, 2011 | Car Speakers & Subwoofers

1 Answer

My Infinity 6 CD Player (2007 KIA Rondo) "displays Error 21" when you try to play, eject or change a CD. Does anyone know what this is?


Personally, if it were me, I would replace your indash changer with an aftermarket single disc player. Indash changers are notoriously unreliable and go bad very easily.

Jun 01, 2011 | Car Speakers & Subwoofers

1 Answer

Fiona@jossi have a mazda 3mps with 6 disc changer 3 of the discs wont eject and it keeps saying check cd. discs wont play either. can anyone help please!!!


sounds like you are using discs you have burnt yourself

these discs are thicker than the ones you get in stores and frquently get stuck and dont work in units not built to handle these discs

it is very hard to get out without removing unit and opening it

you might be able to carefully grab or hook disc if it partially ejects but you risk damaging disc or unit you might need to bring it to repair shop

good luck

Mar 13, 2011 | Car Speakers & Subwoofers

1 Answer

I hav a clarion auto cd/stereo displaying err 6 please explain, thank you


Error 1.Battery inside CD Changer needs to be replaced.
Error 2.CD error message. Mechanism has as eject problem or takes a long time to select CD.
Error 3.CD error message. The pick-up is out of focus during play mode due to scratches on the disc or contamination.
Error 4.Connection problem. Reconnect the data cable.
Error 5.CD error message. Could not read correct data due to CD ROM.
Error 6.CD error message. Could not read data from disc because it is upside-down.

For error code 6:
Try an original purchased cd with no scratches and see if the cd player reads it. If yes then lens is dirty or tired so try using a cleaning cd(has little brushes on it). If it doesn't read with the original cd try using the cleaning cd and if no go then look at purchasing a new cd player!

Nov 01, 2010 | Car Speakers & Subwoofers

1 Answer

When i change from radio or single disc to the 6 disc changer there is an error it won't read any discs.... It wont even change discs it won't do anything really...


I suspect that your 6 cd changer is having the fault. The error indicates always a system malfunctioning. From our point of view we can probe into for a solution by the following guidelines.
first of all open the 6 Cd changer from the top. look within to find that the changer is jammed inside. If so slowly tapp while you switch on the power. if the jamm clears and the changer ejects, then open out all the cd's present in the changer for any damage due to heat. If this did not solve, clowing chek for foreign particles/dust that has blocked the loading drive.from completing the cycle so as to reset the mode. normally all errors show because of the processor not receiving the complete cycle signals. hence check for all the moving parts, the drives and the loading mechanism. check also for any linkage damge, any leadd specially flexible line wiring to the motors for an open circuit. Slowly turn the motor drive to intiate to confirm if the motor has failed. Altogether use a multimeter and check in all the sections described.
I hope this helps. Good day.

Jun 28, 2010 | Car Speakers & Subwoofers

1 Answer

I have a 6 cd changer is my Sebring. It was playing disc #2 and I decided to change to disc #5. An error appeared on screen and now I'm unable to get the Cd player out. I think the two disc got stuck as...


get two wires and hook one of them up to the radio on the power wire and ground it and press eject and rub yout stomache and pat your head and hop on one foot and try to bite your ear and it should be fixed

Jul 05, 2010 | Car Speakers & Subwoofers

1 Answer

Jensen hd5112 error 2


CD Changer Error Codes: If problems arise during CD changer operation, the following error codes may appear in the display:
ER-1: No magazine loaded.
ER-2: Problem in the disc loading function.
ER-3: Error in the disc loading function.
ER-4: Error in the disc unloading function.
ER-5: Error in the magazine position.
ER-6: Error in the laser pickup position.
ER-7: Error in the laser focus on the disc.

Dec 21, 2008 | Car Speakers & Subwoofers

1 Answer

Have a Blaupunkt AM FM Radio/In-Dash Ch Cgnager (6 stacker) in a 2003 Holden Commodore. After ejecting the 6th one of the CD's succesfully, get "CD Error mech" message and it will not eject the...


We eventually tried loading another CD to fill the one vacant spot we knew was in the changer even though we'd tried that before without success. This time it seems that we fluked it just as it was trying to eject CD 1 again and - somehow - the CD we were tryng to insert must have lifted the rim of the one that was stuck and it suddenly ejected. The remaining 4 CD's that were inside the changer but not even recognised, then started re-loading so it appears that they were all jammed up together. Once they'd reloaded we were able to eject them all successfully then reload.
We're not sure but think that it may have happened when the eject button was originally pressed once to eject CD 6 then, in error, held down for a 'eject all' procedure and the changer has become confused with both instructions.

Jun 01, 2008 | Blaupunkt Car Speakers & Subwoofers

Not finding what you are looking for?
Car Speakers & Subwoofers Logo

Related Topics:

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Speakers & Subwoofers Experts

xxxxxx xxx

Level 3 Expert

4706 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Car Speaker and Subwoofer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...