Question about Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

1 Answer

F&P dish drawers model DD6031

Top drawer keeps beeping. takes a few goes for it to actually start. then it will stop and beep. even when it gets through a cycle and is turned off... its turns itself on and starts beeping intermitantly. annoying at 2am in the morning....

Posted by on

  • stellatdj Apr 26, 2008

    i have the same problem. Just the top drawer intermittently beeps and power's up like I have opened the drawer.... i have ignored it, and it eventually turned into an F1 error, which I have now fixed... but now back to the intermittent beeping problem.

  • Anonymous Mar 26, 2014

    when I close door no cycle lights come on , it continue to beep and wont turn on.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 413 Answers

It may be that the DW thinks the drawer may have been pulled open. On the right side, near the top. there are two light pipes on the drawer. One sends an infrared beam of light to a reflective area on the cabinet, the other receives this light. This is how the drawer senses whether the drawer is open or closed. Wipe these areas with a clean dry cloth.

Posted on Jun 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Top half of my dish washer beeps when i push the power button


you will find this diagnostic service document useful.

http://applianceassistant.com/ServiceManuals/dishwasher-fisher-paykel-dish-drawer-dd603-ds603-service.pdf#zoom=100#scrollbar=1

The likely reason for top drawer not starting wash program when you press start button is the drawer home sensor is either faulty or the drawer is misaligned. This means controller thinks the drawer is open and does not start the cycle.

Apr 28, 2014 | Fisher and Paykel 23 in. DD-603SS Built-in...

1 Answer

No power top drawer


Try to reset your dish washer. Turn off main power supply and leave it for at least 1 min. Is there any error code appear/beeping sound?

Sep 09, 2007 | Fisher and Paykel 24 in. DD603H W Built-in...

1 Answer

Dishwasher beeps but won't run


There could be several reasons for the beeping. The dishwasher checks for sensor to make sure it is in good health before it starts. Most likely the drawer close sensor is detecting fault. This is to ensure the drawer is closed fully to avoid water leaks when dishwasher is on. Sometimes sensor itself has failed and has nothing to do with position of drawer. Open top cover carefully to make sure the drawer is travelling ok on the rails. TAKE MAINS POWER CABLE OUT BEFORE WORKING ON DISHWASHER.

Mar 17, 2013 | Fisher and Paykel DD24DCTB6 Builtin...

1 Answer

Top drawer on F&P dish drawer stuck on cycle & continuously beeping


You could isolate the top drawer by taking the controller power cable out. DIsconnect mains power to dishwasher, open top drawer and remove front cover carefull after removing 2 plastic pins on each side with plier. Controller box is on left top side, remove bottom connector and cover with insulation tape. Put things back and turn power back on.

But if you want to find the fault with top drawer then that is very trick if there is no fault code on panel except beeping First clean the top panel inside door with a clean damp cloth. If this does not change the situation, then it is very likely the controller is detecting some faulty sensor - and will need to find one by one. Are you ready for it?

Dec 17, 2012 | Fisher and Paykel 23 in. DD-603SS Built-in...

2 Answers

The top dish drawer turns on but won't go. It comes up with a little clock and counts up to about 11 or 12 then goes off. It continunally beeps and won't actually start up.


Hi,
Somehow your drawer was put into a showroom mode. In this model, with the power off, push ECO and Power button for 5 seconds. (ECO first then Power and hold for 5 seconds) this should clear this out.
If you still have issues seen me another message and I will respond as quick as possible. Taking my daughter out to a party tonight.

Aug 27, 2011 | Fisher and Paykel 23 in. DD-603SS Built-in...

2 Answers

My FP Dish Drawer beeps and won't start. The bottom drawer makes the same beeping sound - four quick beeps - as if it were not closed when I try to start it. Dishes are stacked properly and of course...


Hello & Welcome to FixYa

The problem is with the control board that is bad and needs replacement. Please get back to me if you have any other questions.

Kevin

Aug 01, 2011 | Dishwashers

1 Answer

My fisher dd6031 bottom drawer doesn't seem to get rid of all the water,,and it keeps beeping and will keep beeping through the night if you don't catch it...we have been putting it through another rinse...


You will have to take the filter plate out the motor rotor out. Then clean the rotor cavity and replace in reverse order.

Are you getting any error codes?
Does the beeping stop if you turn the power off and on?

Sep 05, 2010 | Fisher and Paykel 24 in. DD603H W Built-in...

1 Answer

We have the Q 2 drawer dishwasher stopped working.


the f1 is the flood sensor....a leak has accured....either a dish to larger or lid motor has failed. will need to remove bottom drawer and soak up water and then let air dry for a day or two....turn off the breaker this will keep it from beeping and running the pumps....after drying unit will run, but need to watch the dishes you put in drawers.

Jun 30, 2009 | Fisher and Paykel DD605HSS 23 in. Built-in...

2 Answers

Bottom drawer won't clean or drain


My top draw F&P won't drain, it seems to want to go thru the cycle, but then leaves about 3 inches of water. no codes are displaying. No extra beeping. please help!

Jun 30, 2009 | Fisher and Paykel 23 in. DD-603SS Built-in...

2 Answers

F 1 Error, blinking, beeping and will not stop even when turned off, so we had to turn the circuit breaker off to stop the noise.


You have a leak.
Either from the top lid seal or bottom lid seal. A s time goes by the water level activates the sensor causing the beep. It won't do anything until you fix the leak.

May 25, 2009 | Fisher and Paykel 23 in. DD-603SS Built-in...

Not finding what you are looking for?
Fisher and Paykel 24 in. DD603H W Built-in Dishwasher Logo

486 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Dishwashers Experts

Gere knutson

Level 3 Expert

842 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Blake

Level 2 Expert

136 Answers

Are you a Fisher and Paykel Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...