Question about Thomson 21DC320 21" TV

1 Answer

TV Plasma power on off suddely.

When i power on to start program, it will off immedialy.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Power supply o.k,but set is continuously in stand by mode.

Posted on Sep 09, 2008

  • semsamjongsa Feb 27, 2012

    try dis by changing power supply cord, may b this thing work

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tv goes on then turnsimmeditaly


Short circuited component/s at its main board. Contact any service technician. Gopakumar Gopalan Google

Feb 10, 2014 | Mitsubishi CS-32207 TV

1 Answer

Tv picture will not come on standby is flashing


If the TV goes in standby, then it is in protection mode.

Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box
connected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.

If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |


On LCD Pay particular attention at inverter and power board, power board can be inspected looking for bulged or leaking capacitors, then tested with a multimeter. The inverter is more difficult to test , there is need to read voltages, should be done by a tech. Also the LCD controller board can cause same problem

On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.

On Rear Projection : check lamp, lamp ballast, power board, and convergence.

On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.

Apr 23, 2009 | Sony KV-36FS100 36" TV

1 Answer

Tv has got stuck on standby mode


If the TV goes off completely, then is usually a faulty power board.

If the TV goes in standby, then it is in protection mode.

Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box
connected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.

If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |


On LCD Pay particular attention at inverter and power board, power board can be inspected looking for bulged or leaking capacitors, then tested with a multimeter. The inverter is more difficult to test , there is need to read voltages, should be done by a tech. Also the LCD controller board can cause same problem

On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.

On Rear Projection : check lamp, lamp ballast, power board, and convergence.

On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.

Apr 22, 2009 | Bush 5693D 24" TV

1 Answer

Tv dead,checked fuse plug OK


If the TV goes off completely, then is usually a faulty power board.

If the TV goes in standby, then it is in protection mode.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.

If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |


On LCD Pay particular attention at inverter and power board, power board can be inspected looking for bulged or leaking capacitors, then tested with a multimeter. The inverter is more difficult to test , there is need to read voltages, should be done by a tech. Also the LCD controller board can cause same problem

On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.

On Rear Projection / LDP : check lamp, lamp ballast, power board, and convergence.

On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.

Mar 27, 2009 | Televison & Video

1 Answer

Sony model # KV32S42. The TV started flashing when first powering up. The flashing would continue 4 or 5 times before TV would eventually stay on. The last time I tried to turn it on I heard a dull thud...


If the TV goes in standby, then it is in protection mode.

Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box
connected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.

If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |


On LCD Pay particular attention at inverter and power board, power board can be inspected looking for bulged or leaking capacitors, then tested with a multimeter. The inverter is more difficult to test , there is need to read voltages, should be done by a tech. Also the LCD controller board can cause same problem

On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.

On Rear Projection : check lamp, lamp ballast, power board, and convergence.

On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.

Feb 24, 2009 | Sony KV-27S20 27" TV

1 Answer

Cant turn tv on when red light is flashing


If the TV goes in standby, then it is in protection mode.

Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box
connected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.

If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |


On LCD Pay particular attention at inverter and power board, power board can be inspected looking for bulged or leaking capacitors, then tested with a multimeter. The inverter is more difficult to test , there is need to read voltages, should be done by a tech. Also the LCD controller board can cause same problem

On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.

On Rear Projection : check lamp, lamp ballast, power board, and convergence.

On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.

Feb 13, 2009 | Bush WS6671 28" TV

1 Answer

Tv keep flashing.


If the TV goes in standby, then it is in protection mode.

Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box
connected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.

If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |


On LCD Pay particular attention at inverter and power board, power board can be inspected looking for bulged or leaking capacitors, then tested with a multimeter. The inverter is more difficult to test , there is need to read voltages, should be done by a tech. Also the LCD controller board can cause same problem

On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.

On Rear Projection : check lamp, lamp ballast, power board, and convergence.

On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.

Feb 02, 2009 | Sony KV-32S40 32" TV

1 Answer

32" rca 32v524t


If the TV goes in standby, then it is in protection mode.

Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box
connected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.

If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |


On LCD Pay particular attention at inverter and power board, power board can be inspected looking for bulged or leaking capacitors, then tested with a multimeter. The inverter is more difficult to test , there is need to read voltages, should be done by a tech. Also the LCD controller board can cause same problem

On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.

On Rear Projection : check lamp, lamp ballast, power board, and convergence.

On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.

Jul 13, 2008 | RCA 32V524T TV

1 Answer

Bush 26 lcd tv


If the TV goes off completely, then is usually a faulty power board.

If the TV goes in standby, then it is in protection mode.

Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box
connected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.

If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |


On LCD Pay particular attention at inverter and power board, power board can be inspected looking for bulged or leaking capacitors, then tested with a multimeter. The inverter is more difficult to test , there is need to read voltages, should be done by a tech. Also the LCD controller board can cause same problem

On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.

On Rear Projection : check lamp, lamp ballast, power board, and convergence.

On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.

Apr 05, 2008 | Bush 5693D 24" TV

1 Answer

Airane


If the TV goes in standby, then it is in protection mode.

Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box
connected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.

If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |


On LCD Pay particular attention at inverter and power board, power board can be inspected looking for bulged or leaking capacitors, then tested with a multimeter. The inverter is more difficult to test , there is need to read voltages, should be done by a tech. Also the LCD controller board can cause same problem

On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.

On Rear Projection : check lamp, lamp ballast, power board, and convergence.

On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.

Jan 26, 2008 | RCA 32V524T TV

Not finding what you are looking for?
Thomson 21DC320 21" TV Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Thomson Televison & Video Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

69887 Answers

 Grubhead
Grubhead

Level 3 Expert

4678 Answers

Are you a Thomson Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...