Question about Projection Televisions

1 Answer

Hitachi projection tv cannot seem to focus the red lamp. Auto focus helps a little bit, but picture is still very out of focus with red streaks and shadows. Problem happened overnight. Model # 61UWX10B.

Posted by on

  • eDad2003 Apr 25, 2008

    Have the same problem with 53UWV10B, but green. Looks like 3 extra shadows off to the right, everywhere on the screen. Could be interpreted as 3D I guess.



    Most noticeable when white lettering is on the screen, like it's casting a bright green shadow to the right.

  • eDad2003 Apr 25, 2008

    oops, model no is 53UWX10B.



    Also only happens when TV warms up. Cold TV is perfect. And in happened in an instant, not gradually deteriorating

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 121 Answers

Does the red look like its 3D or is it just blurry let me know I may be able to help you

Posted on Apr 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a red X on screen of my Hitachi 57f510 HD tv. What does that mean?


It may have to do with the Magic focus if that model has it: auto convergence and if fails a indication can appear on screen. The Magic focus if in play would be a flashing sequence moving to different areas of the screen in sequence.

Dec 09, 2012 | Hitachi 57F510 57" Rear Projection...

1 Answer

My Hitachi 46F500 TV will not adjust either manually or in magic focus mode......it has green lines across top of screen and some red tinting in the picture ......is this a gun issue or mirror in need of...


Hello,

Replacing the lamp will do the job. It is the lamp that is faulty not the gun or the mirror.

It will cost just a few box to get a new lamp.

Take care and good luck

Oct 10, 2010 | Hitachi 46F500 46" Rear Projection...

1 Answer

Color red seems to be more prominant...than other


I've had this problem with my projection TV recently. I would say your lens/lamp is to blame. It might be time to change it, depends on the last time it was changed, most of the time, the TV will tell you that it needs to be changed, but not always. I think your best bet is the TV lamp.

Oct 20, 2009 | Hitachi Projection Televisions

1 Answer

Plenty of Sound, No Picture


You may have to replace the convergence IC's or the lamps. Impossible to say without having a manual inspection. Best bet is to take it in for a service repair..

Sep 27, 2008 | Hitachi 50UX26B/27K 50" Rear Projection...

1 Answer

50ux26b Hitachi


Good Day;

Sounds like the Convergence Circuit in the TV has failed. Call an Authorized Service Center and have them come out and give you a wtitten estimate B4 repair.

Good Luck, big IRISH.

Sep 27, 2008 | Hitachi 50UX26B/27K 50" Rear Projection...

1 Answer

Double focused, red and green, bow in picture top and bottom


hi
You have a convergence problem
If the set has auto focus and will not complete its cycle.
The Auto focus module is bad, (expensive)
If it completes and the problem is still there.
Then check for bad conv. drivers (stk****) or cold solder joint on one or more of the 3 drivers pins.
Guy9

Jul 08, 2008 | Hitachi 65S700 65" Rear Projection HDTV

1 Answer

Hitachi 61SDX picture got dim shows Code 3


use the advanced options page and reset the factor blue and red convergence defaults then do re apply the auto color defaults color at first it seemed very red (which is good because red was the missing factor in the green picture) but after reseting all the color and tints to the normal ranges I then reset the color auto correct again and all seems fine.

Nov 17, 2007 | Hitachi 61SDX01B 61" Rear Projection...

1 Answer

Hitachi 52 projection tv


use the advanced options page and reset the factor blue and red convergence defaults then do re apply the auto color defaults color at first it seemed very red (which is good because red was the missing factor in the green picture) but after reseting all the color and tints to the normal ranges I then reset the color auto correct again and all seems fine.

Jan 22, 2007 | Hitachi 50V710 50" Rear Projection...

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60792 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...