Question about Audio Shelf Systems

1 Answer

Can't remember how to wirer my stereo

I have a kenwood stereo system i bought in about 1997. it's a km894. where can i get a wirering diagram

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 150 Answers

For a full service manual, try this site:

http://www.servicemanuals.net/results.aspx?type=SM&brand=16&model=KM894

If you are only interested in connecting your stereo to other components, write down all the labels from the rear connector
panel, and I will try to identify them for you

Martin

Posted on Apr 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I get sound out of my kenwood stereo system?


Ask the previous owner to demonstrate how it works

Sep 21, 2014 | Kenwood XD-A8 CD Shelf System

2 Answers

Stereo plug color wire to pin


all you must do is check the colours on your sockets and match them white and red is your speakers and yellow is your visual

May 27, 2013 | Audio Shelf Systems

1 Answer

I need to buy an AM antenna for my Kenwood XD-452 Stereo. Can anyone help?


I assume you have the AM antenna which came with your system -- but in any event, here is a very broad selection of AM antennas.

http://www.thefind.com/electronics/info-am-loop-antenna


Charlie

Jan 12, 2011 | Kenwood Audio Shelf Systems

1 Answer

When i turn on , the display is" PROTECT " KENWOOD XDA55


make sure the speaker wires aren't shorted anywhere.....a short normally activates protect mode on most stereo systems.

Oct 22, 2010 | Kenwood XD-655 CD Shelf System

1 Answer

I have an old kenwood shelf system, with the following components:kenwood stereo power amplifier B-A9 100v 125w, kenwood C-A9 digital pre-amplifier/tuner, kenwood stereo cassette deck x-A9 plus a cd...


Thanks for your concern. I was badly in need of a manual and luckily enough I got across a friend who had one in Uganda. So that solved my problem.

Jan 01, 2010 | Kenwood XD-A55 CD Shelf System

2 Answers

Kenwood KDC-W312S wont keep the saved channels after car restart


Check the yellow wire connection on your wiring harness... This is the wire that provides continuous power even when the ignition is off. This is how the radio remembers presets/time and such. Every time you turn off the car, the radio "resets" because you dont have the yellow wire connected to an ALWAYS HOT wire.

If you cannot find a hot wire, then you can run a wire from the yellow on the back of your radio directly to the positive terminal on your battery. Dont worry, it doesnt draw enough power to run your battery down.

Most cars have a cigarette lighter or power port somewhere that is always hot. You could always run the yellow wire off of one of these.

Just find a way to get the yellow wire on a hot wire and your stereo will remember the presets.

Mar 29, 2009 | Kenwood M-303USB Shelf System

1 Answer

Conection to my computer


I burn CD's on my laptop connected to a HM-33 through the earphone out plug. You have to change the computer's system input sound preference from "system" to "Audio in". Stereo sound quality is excellent.

Sep 04, 2008 | Kenwood HM-333-S Shelf System

1 Answer

Surround sound speakers


two rms-70 watt are good enough for you.

Jul 16, 2008 | Audio Shelf Systems

1 Answer

Kenwood XD 550 stereo start-up problem


this normally happens with a lot of sets! It usually happens during a Power Failure, Power Surge (Fluctuation) and if the wire of the component is taken out from the wall outlet while the system is on...To get rid of this problem all you need to do is to press the Display button on the main unit, it is located just below the main display! Voltage Selection has got nothing to do with this problem...

Jun 29, 2008 | Jwin JK-777 Nostalgic Stereo System with...

1 Answer

Installing a cd player dp-87 on a component stereo


Its easy i think your chinch cables are not good try with other pair of chinches and if it not work try to change the speakers from a to b position on your amplifier if that doesnt work probably its the one chanell on your cd is not working.

Jun 14, 2008 | Audio Shelf Systems

Not finding what you are looking for?
Audio Shelf Systems Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio Shelf Systems Experts

The Knight
The Knight

Level 3 Expert

68197 Answers

 Grubhead
Grubhead

Level 3 Expert

4576 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you an Audio Shelf System Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...