Question about Numark BATTLE PAK v.4 Turntable

1 Answer

NUMARK TT 1625

MY HUSBAND PURCHASED A NUMARK TT1625 FROM A PAWN SHOP & NEEDS TO REPLACE THE NEEDLE. WHAT NEEDLES ARE COMPATIABLE OR WHERE CAN HE FIND ONE?

Posted by on

  • neroonela
    neroonela May 07, 2012

    u can buy the next up grade
    numark cc-1, for me is been the best of the price and service..
    any were from $50 - $80 depending were u live at!. but for the price is a great quality and sound.. so spend that extra dollar and have fun with ur records..
    paz amour muxic dj nero one..

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 515 Answers

Any of the following cartridges will fit your turntables:

CARTRIDGES @ 1200s.com

I don't suggest using the originals that came with the turntables, as they aren't of the greatest quality. For a small investment (about $50), you can get some better quality cartridges/needles.

- Davis
DJ Pro Audio
www.DJPROAUDIO.com
www.REPAIRNYC.com


Posted on Jul 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The plate on my numark tt USB is wobbiling


I find it hard to believe some of these answers. If the platter is wobbling, if you remove the platter, you'll find the spindle the platter rotates on. That will probably be loose. At the bottom of the spindle bearing, you will find a nut. Tighten that, and you should be in business. If you have further questions please visit my website at audioserviceclinic.com. You may contact me there.

Apr 26, 2015 | Numark ttUSB Turntable

1 Answer

Numark needle broke


Generally yes. Just type the cartridge number into Google and it should find the right stylus - not needle!!!

Dec 28, 2012 | Numark ttUSB Turntable

1 Answer

How do i hook a numark tt 1625 turntable to a regular home stereo amplifier...does the ground need to go into anything specific?


Turntables require a special input in the amp (usually marked PHONO) because they require high gain and different equalization - and yes, that ground wire has to go to ground unless you want to get a super annoying 60Hz hum from it!
If your amp doesn't have a phono input, you're going to have to go out and get a phono pre-amp and connect it between the turntable and the amp.
Best of luck!

Feb 26, 2011 | Numark TT1650 Turntable

1 Answer

I can't find a needle/cartridge for my turntable, it's a Numark TT-1910


if you have the headshell left with the 4 little wires hanging out then you will need a complete cartridge.
turntableneedles dot com/Half-Inch-Standard-Mount_c_49632.html
if you have the cartridge part then it's still good and you only require a new needle. Type your cartridge number into the search window at the above website.

Apr 24, 2010 | Numark TT1910 Turntable

1 Answer

No signal coming from rca output on numark pro tt-1 turntable.


Please recheck all connections from the 'needle' to the end of your hook-up cable. Check with a continuity checker if you have one (volt/ohm meter will do nicely)

Mar 11, 2010 | Numark Pro TT-2 Turntable

1 Answer

When I scratch with my numark tt1625 its very slow to spin again


Try Changing The Slipmats Gemini Slipmats Are More Slippery Than Standard Numarks I Use ThudRumble Frosted Plates In Place Of My
Original SlipMats On My 1650's

Jan 19, 2010 | Numark BATTLE PAK v.4 Turntable

1 Answer

Numark tt1625 turntable wavey sound


Your belt is probably worn and needs replacing. Lift felt on platter and and lift the platter section off the unit by putting your thumb and forefinger through the two large holes and pull upwards.There should not be any special routing for the belt and should go directly onto the spindle motor to your platter. Place the belt around the inside rim of the platter while it is still off the unit. Now replace the platter and move the platter around until you see the spindle motor through one of the holes. Use some tweezers to manouvre the belt onto the spindle motor. On some units you will have to lay the belt out inside the unit, replace the platter and manouvre the belt onto the platter. Hope this helps

May 28, 2009 | Numark BATTLE PAK v.4 Turntable

1 Answer

Numark tt1625 keeps on jumping


If your weight and such are correctly set, then the only other issue might be a worn stylus, or your tonearm might be damaged.

- Davis
We are the Turntable Experts!
DIGITAL ANALOG THERAPY

Aug 08, 2008 | Numark Turntables

2 Answers

My numark tt1625 turntables keep slowing down


If you could be a little more specific, we might be able to help you out better.

Does it slow down, when you do anything, or after a long period of time of being on/used? Or as soon as you turn it on, it slows down?

Any specific information would be greatly appreciated.

- Davis
DJ Pro Audio
www.djproaudio.com

Jul 14, 2008 | Numark BATTLE PAK v.4 Turntable

Not finding what you are looking for?
Numark BATTLE PAK v.4 Turntable Logo

Related Topics:

2,374 people viewed this question

Ask a Question

Usually answered in minutes!

Top Numark Turntables Experts

 Grubhead
Grubhead

Level 3 Expert

4576 Answers

Jazz Boyce
Jazz Boyce

Level 1 Expert

728 Answers

Steve

Level 3 Expert

3287 Answers

Are you a Numark Turntable Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...