Everytime I try to make an outgoing call, I get a message "handset out of range" and I cannnot complete the cal

Registering a Handset

If you see a "not registered" message on a handset, you must register it to a base before using it.

1. On the base, open the menu and select "Register Handset"

2. On the handset, press and hold POUND (#) until the handset display says "Handset Registering" (about 2 seconds).

3. Wait until the handset display says "Registration Complete" (about 30 seconds), then pick up the handset and press eND/CleaR.

# If you don't hear a dial tone or the display says "Registration Failed" charge the battery completely, then try again.

The KX-TGA740 is a cordless handset. The outgoing message is on the answering machine. Please consult the documentation for whatever answering machine you have on your phone line. If you require further assistance, please reply to this post and specify the make and model of the answering machine.

Which model phone do you have? For the CL82509 and related DECT 6.0, you need to set the outgoing message from the handset when the answering machine is on. (It can be turned on from the handset).

For the outgoing message: with the handset in Idle mode, press Menu/Select. Use the up (Dir) and down (CID) arrows to highlight Ans Sys Setup. Then press Menu/Select. Use the same arrow keys to select Announcement and press Menu/Select again. Press 7 to record a new announcement. At the tone, speak your message clearly then press 5 when you have ended the message. The message will play back.

This model's manual is available here: http://att.vtp-media.com/ecp/documents/product_Product/132/UserManual/5995/cl82509_manual_USA_i6.pdf . See page 15 to set the answering system outgoing message. (This is different than Voicemail. To set up Voicemail, you will need to see your telephone provider's documentation.)

Most AT&T phone manuals are available here: http://telephones.att.com/att/index.cfm/product-support/manuals/ .

I hope this helps.

Cindy Wells

To record an outgoing message, this is what you do-Press the voice mail key on the handset to access the answering machine. Then press 8 to record your message.
Hope this was helpful? Please comment for more information and thank you for using fixya

You may download a copy of the manual here. The day/time instructions are on pages 9-10. The outgoing message instructions are on page 21.

Hi,

please follow the instruction to register the handset to base

To register a DCX150 accessory handset:
1. Charge the handset completely.
2.Place the handset in the base cradle for about thirty seconds. Handset Registering will appear in the LCD.
3.When the handset has registered to the base, the LCD will display Registration complete then show the handset ID number.

If the display shows Registration failed, repeat the process again.

To register a DCX200 or DCX300 accessory handset:

1.Charge the handset completely.
2.Disconnect the base AC adapter. Then press and hold find while you reconnect the adapter. Keep holding find until the charge LED starts to blink.
3.On the handset, press and hold # until the handset beeps and displays Handset Registering.
4.When the handset has registered to the base, the LCD will display Registration complete then show the handset
ID number.

If the display shows Registration failed, repeat the process again.

Thanx

These phones have to totally discharge. Unplug the phone from the jack, take out your battery. Wait up to 24hours. This should set it back to factory default. Look for a reset button on your station and on your phone. It is usually the size of a pin hole. Sell what this does. If you need more help be sure to contact me. Thanks.
JimmyC

it depends on the model u r using genrally they don't
bt i wud advise you to call up the company helpline for help

Please check that you have correctly registered the second handset to the base. It may be necessary to de-register the second handset and then re-register it. "Out of range" just means the second handset is not within range of the base phone it was registered to.

the cipering not allowed by operator.insecure transmission.