In need of a replacement lamp for a Mitsubishi WL82913 bulb part #915P016010

Mitsubishi change side lamp bulb mitsubishi space wagon ...

www.fixya.com > ... > change side lamp bulb mitsubishi space wagon

Change side lamp bulb Mitsubishi space wagon related problems. Ask your Change side lamp bulb Mitsubishi space wagon questions. Get free help, advice ...

Mitsubishi Space Wagon 91 98 Sidelight Bulbs W5W 501 ...

www.ebay.com > ... > External Lights & Indicators > Bulbs & LEDs

eBayProduct Type: Sidelight. Operates: Sidelight. Further Information: These bulbs are a direct replacement for any W5W 5W (501) wedge bulb no matter what brand.

ebay, https://www.bing.com/videos/search?q=mitsubishi+rear+projection+tv+ws+65809+bulb+replacement&qpvt=Mitsubishi+rear+projection+TV+WS+65809+bulb+replacement&FORM=VDRE

You can try ordering this from Express Repair Center.

2196 NW 82nd ave.
Miami FL 33122

Toll Free 1-877-260-9965
tel: 305-500-6334
fax: 305-500-6339


You can also order this part from their page, but I would recommend you to call them before placing any orders, the link to the page is:

http://www.ercservice.com/lamps/mitsubishi-lamps/915P016010.html

Try reading here since it is so old:
http://www.bulbtogo.com/rear-projector-tv-/-rptv/915p016010-lamp-for-mitsubishi-wl-82913-rear-projection-tv/prod_5773.html

http://www.fixyourdlp.com/forum/viewtopic.php?t=554

bulbto go.com $169.00 plus s+h,however,get housing for bulb as well-this will probably save you many problems.

bulbtogo.com 169.00 +s+h

bulbtogo $169.00 plus S+H

Your access should be a a panel near the back or side. You will see that it is somewhat easily removed and should have maybe one or two screws. You will see the casing to the lamp. Go ahead and remove it. Now unscrew the old bulb and replace it with a new one. There is not a lot of screws holding it together. It's a fairly easy process once you find the lamp. You should see the lamp once the panel is removed.

I had the same issue when replacing my lamp for the first time. I replace just the bulb with the Phillips replacement bulb. After installing the power down issue started and it would take up to 7 attempts before the TV would stay on with a picture.

Since I never had this problem until i replaced the bulb i decided to send the new bulb back and replace it with a difference one. In my opinion replacement parts are never made to the same standard as original OEM parts. This TV is definitely very temperamental in regard to the bulbs.

When the second replacement bulb arrived I decided to not only replace the bulb I also cleaned the connector plug in the cartridge with a QTip and alcohol. I did the same for the plug receptor in the TV.

When I replaced the bulb i insured the the top of bulb lettering was facing the handle of the cartridge so when you put the cartridge back in the TV the top of the bulb would be facing you.

I also cleaned the entire inside of the TV where the cartridge is inserted including the screws.

Once I did all this the TV turned on the first time and has been working fine for three days now.

I do believe the replacement bulb position is very important as to how it heats up and determines when it needs to cool.

I hope this helps others with the same success i had because I really do not want to replace this TV and start replacing all the parts others have done with little to no success for this issue.

The file is too large to post here but if you post your email address, I can send you the step by step instructions to replace the lamp and reset the lamp hour counter.