Question about Kyocera FS-720 Laser Printer

1 Answer

Printer FS720 Kyocera: both leds on both off for

Printer FS720 Kyocera: both leds on both off for few seconds both leds blinks 3 times green led blinks 2 times both leds blink once freen led blinks 2 times

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Read here :
http://www.fixyourownprinter.com/forums/laser/64772

Posted on Aug 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kyocera fs 1030d: first sequence: 1.led:green


THE PROBLEM IS THE FUSER, YOU HAVE TO OPEN THE ENTIRE TEAM AND IN THE BACK OF PART WHERE IS HEATS UP THE PAGE, BETWEEN ROLLER GREY AND ORANGE, ALLI THIS FUSER. HIM REMOVING THE ENTIRE PIECE THIS SUBJECT TO TWO SCREWS, YOU MUST DISCONNECT THE CABLES (THREE PAIRS), THE PIECE THAT YOU JUST EXTRACTED HAS TWO SCREWS THAT HOLD A BONBILLO THAT IS INSIDE THE GRAY CYLINDER, THERE BELOW YOU WILL SEE A SMALL WHITE PIECE THAT IS SUSTAINED BY TWO SCREW WHICH ARRIVE TWO CABLES, THE DRAW AND THEN TO THE WHITE PIECE WITH A FINE NEEDLE HIM GOING TO PASS UNDERNEATH AND CAREFULLY RAISE THE BLACK PARTIF THE VERIVICAS SHOULD GIVE CONTINUITY WITH EN MULTIMETRO O METER OF VOLTAGE. IF YOU WANT THE CAN BUY ALSO IN AN ELECTRONICA. SORRY ENGLISH

Aug 17, 2011 | Kyocera Mita FS-1030D Laser Printer

1 Answer

Cant print anymore print counting is almost full. how to reset count


try this

Manual reset methods several EPSON Stylus Color. Actually there are two methods to reset epson printers counter, that is using software resetter such as adjustment program or SSC service utility or using manual by combination pressing button on the printer. If Reset using software resetter you can follow the way of usage the software but sometimes software resetter for the printer is not available. The only way to reset the printer if software resetter not available you can use manual reset.
The Following manual reset for some EPSON Stylus Color Printers:
1. EPSON Stylus Color
Pressing and holding ALT+FONT+LOAD+PAUSE buttons combination
press POWER button
Release all buttons
2. EPSON Stylus Color 300
3. EPSON Stylus Color 400, 600
Pressing and holding LOAD/EJECT and CLEANING buttons
press POWER button and hold it until you will see blinking INK OUT and PAPER OUT leds
Release all buttons
In 2-3 seconds time press LOAD/EJECT and CLEANING buttons again.
4. EPSON Stylus Color 440, 640, 740, 460, 660, 670, 760, 860, 880, 1160
Pressing and holding LOAD/EJECT and CLEANING buttons
press POWER button and hold it until You will see blinking INK OUT and PAPER OUT leds.
Release all buttons.
In 2-3 seconds time press and hold CLEANING button, until all leds will blink.
5. EPSON Stylus Color 680
Pressing and holding LOAD/EJECT and CLEANING buttons,
press POWER button and hold it until You will see blinking INK OUT and PAPER OUT leds.
Release all buttons.
In 2-3 seconds time press and hold LOAD/EJECT button, until all leds will blink.
6. EPSON Stylus Photo 785, 895
Pressing and holding Maintenance and Roll Paper buttons
press POWER button, You will see blinking Error led.
Release all buttons.
In 2-3 seconds time until led is blinking press and hold for 10-12 seconds Roll Paper button, until all leds will blink.
7. EPSON Stylus Photo 890, 1280, 1290
Pressing and holding Maintenance and Roll Paper buttons, press POWER button, You will see blinking Power led
Release all buttons
In 2-3 seconds time until led is blinking press and hold for 10-12 seconds Roll Paper button, until all leds will blink
In 2-3 seconds time press LOAD/EJECT and CLEANING buttons again.
8. EPSON Stylus Color 800, 850
Pressing and holding LOAD, CLEANING Color and CLEANING Black buttons
press POWER button and hold it until You will see blinking INK OUT and PAPER OUT leds.
Release all buttons.
In 2-3 seconds time press and release CLEANING Color button, You will see leds blinking.
9. EPSON Stylus Color 900, 980
Pressing and holding LOAD/EJECT and CLEANING buttons
press POWER button, You will see blinking INK OUT led
Release all buttons
In 2-3 seconds time press and hold CLEANING button for 10-12 seconds.
10. EPSON Stylus Color 3000
Pressing and holding PAUSE, LF/FF and DOWN ARROW buttons
turn on printer.
Release all buttons.

Mar 17, 2011 | Computers & Internet

1 Answer

Printer jamed after putting in more paper and accidently pushed the power button off. Will not respond to anything I have tried.


Reset your Printer by following these steps for your Printer Model:

EPSON Stylus Color 900, 980
Pressing and holding LOAD/EJECT and CLEANING buttons, press POWER button, You will see blinking INK OUT led.
Release all buttons.
In 2-3 seconds time press and hold CLEANING button for 10-12 seconds.
EPSON Stylus Color 3000
Pressing and holding PAUSE, LF/FF and DOWN ARROW buttons turn on printer.
Release all buttons.
EPSON Stylus Photo 785, 895
Pressing and holding Maintenance and Roll Paper buttons, press POWER button, You will see blinking Error led.
Release all buttons.
In 2-3 seconds time until led is blinking press and hold for 10-12 seconds Roll Paper button, until all leds will blink.
EPSON Stylus Photo 890, 1280, 1290
Pressing and holding Maintenance and Roll Paper buttons, press POWER button, You will see blinking Power led.
Release all buttons.
In 2-3 seconds time until led is blinking press and hold for 10-12 seconds Roll Paper button, until all leds will blink.

Feb 27, 2011 | Epson Stylus Photo 785EPX InkJet Printer

1 Answer

How Do you clean the Laser scaners on a Kyocera C5025N Printer?


Open the left cover. Then grasp the green tab at the back of each LED unit, sowly pull the tab in and out about the width of the printer 4 to 5 times. This will clean the LED units. You can also use the wire cleaners at the top of each LED unit. For more details consult the operation guide page 3-12.

Apr 16, 2010 | Kyocera FS-C5025TN Laser Printer

1 Answer

Alarm lights keep blinking after I changed my printer ink.


E5 means cartridges error - to fix press the "stop\reset" button for 5-7 seconds and then release it.

You can also try this:

1) With the printer power turned off but connected to a power source, while pressing the Resume/Cancel button, press and hold the Power button.
(DO NOT release the buttons. The Power LED lights in green to indicate that a function is selectable.)

2) While holding the Power button, release the Resume/Cancel button. (DO NOT release the Power button.)

3) While holding the Power button, press the Resume/Cancel button 2 times, and then release both the Power and
Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the Alarm and Power LEDs light
alternately, Alarm in orange and Power in green, starting with Alarm LED.)

4) When the Power LED lights in green, press the Resume/Cancel button the specified number of time(s)according to the function listed in the table below. (Each time the Resume/Cancel button is pressed, the Alarm and
Power LEDs light alternately, Alarm in orange and Power in green, starting with Alarm LED.)

4 times----Green (Power)------Waste ink counter resetting

Apr 07, 2010 | Canon PIXMA MP240 All-In-One InkJet...

1 Answer

TV cant be switch on, RED LED diagnostic Blinks .. 3 times... then 4 times. Please advise probable cause and send sTV hcematic diagram.


Hi, this is main board failure and you will need to replace this vital board. you power board is fine but, it is unable to send a proper current through the main mother board due to the damage at hand.

May 21, 2009 | Sony KV-29FX30 29" TV

1 Answer

Top 3 lights blinking on printer


The flashing of the LEDs you describe indicates a error. If you call the Kyocera Help Desk they can tell you what the error is based on the order and color of the LEDs. They can be reached at 800-255-6482.

Aug 18, 2007 | Kyocera Mita FS-1030D Laser Printer

Not finding what you are looking for?
Kyocera FS-720 Laser Printer Logo

Related Topics:

459 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kyocera Office Equipment & Supplies Experts

Kyocera HP Expert

Level 3 Expert

523 Answers

Chris Schutte

Level 2 Expert

51 Answers

Henry Gertcher

Level 2 Expert

48 Answers

Are you a Kyocera Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...