Question about Dryers

1 Answer

Whrilpool gas dryer

My whirlpool gas dryer will cont condinually stay hot. I have checked the vents. I have completely disconnected the dryer vent. The gas will turn on and fire will ignite and stay lit for about 1 minute and then turn off for 5-10 minutes and then fire up again for another minute. It is taking 2 hours to dry a load of laundry. Any suggestions?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 184 Answers

DISCONNECT THE EXHAUST FROM THE BACK OF THE DRYER AND TRY DRYING ONE LOAD OF LAUNDRY. IF THE DRYER WORKS O.K. WITH THE EXHAUST DISCONNECTED, YOU HAVE A RESTRICTION IN THE EXHAUST DUCT SOMEWHERE.

Posted on Apr 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dryer does not dry clothes completely


If your machine is taking that long to dry. You either have a clogged vent to the outside or your gas valve coils are bad. You can check to see if it is your vent by disconnecting it for one cycle. If the unit drys in time then clean your vent. Click Here to see what a clogged vent can do. Click here to see gas valve coils.

Apr 01, 2013 | Whirlpool Duet 7.0 Cu. Ft. Super Capacity...

1 Answer

DRYER VENT PIPE HOT TO TOUCH


there could be a blockage which is preventing the hot air from escaping

Aug 07, 2012 | Whirlpool Dryers

2 Answers

Dryer gets hot, but stays damp inside and clothes don't dry. I removed a birds nest from the outer end of the vent, and there is plenty of hot steamy air coming through, but still having this problem....


The vent is probably still stopped up. You are going to have to pull the dryer out and disconnect the 4" vent hose from the back and inspect the vent all the way through.

May 18, 2011 | Dryers

1 Answer

Whrilpool heavy duty dryer not drying, just replaces the ignitor


Im assuming that you have a gas dryer since you said you replaced the glow plug (igniter). So your problem is most likely with lint in the vent hose. Try taking it off and shaking out all the loose lint. If thats not it you could have a gas flow problem. Check your connections for leaks or crimps in and metal hosing.

Dec 12, 2009 | Whirlpool Dryers

1 Answer

Dryer keeps drying and getting too hot


Check the dryer vent .The vent is stopped up,in the vent,or in the inside of dryer,in the lint hopper.Clean it out and unstop the dryer,and the vent.

Oct 10, 2009 | Whirlpool LER5636P Electric Dryer

1 Answer

I have a Whirlpool gold Ultimate Care II gas dryer and 2/3 times the ignitor glows and lights the gas, 1/3 times it won't. When the gas does light, it doesn't seem like it's getting hot enough to do...


I would suggest the coils on the gas valve . Also check the vent to make sure good air flow is getting out of the dryer . Try disconnecting the vent hose and drying a load to determine if maybe the vent is the problem .

Jul 14, 2009 | Whirlpool LGB6300 Gas Dryer

1 Answer

Problem with Whirlpool Duet gas dryer


Hi I have the same problem
Bypassed the hi limit switch and it runs fine
service teck replaced board,thermistor, all vents,gas coils , flame sensor and glo coil andf all with no luck. Unless it is bypassed thed ryer will only stay on 5 to 6 seconds on gas cycle
If i plug my old dryer in and hock up to gas and vent it works fine
So im using my old dryer and this peice of **** is sitting beside it as Im not going to run this without the safety thermostat
If you find out please let me know

Jan 02, 2009 | Whirlpool Duet 7.0 Cu. Ft. Super Capacity...

1 Answer

I have a whirlpool gas dryer.  heats up for a minute than get gool. will not stay hot?


check your exhaust vent to make sure that it is not blocked up with lint. If not then check to see if the flame comes on after the igniter check the peep hole in the front of the dryer.

Dec 28, 2008 | Whirlpool GGQ8831L Gas Dryer

2 Answers

Propane Gas Dryer (Whirlpool DUET Front Loader) not drying


huuum At your service!

Did this tech do some wash to the dryer and feel that there was no heat?
He was not a good tech


Sometimes this can happen when the vent line is clogged.


1. Check if the lint filter is full and needs to be cleaned.
Try this first.
2. Then check if the outside screen covering the exhaust vent if this is even half blocked
with lint there will be no heat! This screen is to keep small animals out!
Try checking this and if it is clogged or the spring loaded door is stuck closed.
Try to clean the lint out of the corners of the flap door,
and or remove the screen permanently!
NO ANIMALS LIKE TO GET BURNT,IT'S HOT IN THAT TUBE! They sense this and stay clear.
It is 2 years that mine is off and all is fine.





You will be fine
Bless You huuum
PLEASE GIVE ME A GOOD RATING BEFORE YOU SIGN OFF!

Jul 11, 2008 | Whirlpool Duet 7.0 Cu. Ft. Super Capacity...

1 Answer

Whrilpool model# LGQ8000JQ1


It might have more than 1 thermal sensor, if you can find a manuel and check. Also if you have a leak on your gas connection(flex hose, ect.)

Apr 09, 2007 | Whirlpool LGQ8000JQ Gas Dryer

Not finding what you are looking for?
Dryers Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...