Question about Margaritaville Frozen Concoction (DM1000) Blender

1 Answer

Need to clean the machine and cannot disconnect the blade on top. My other machine has a button you push and then it releases. this model does not. This is the DM1000 margaritaville machine.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,739 Answers

The Manual for the DM1000 is available here:

http://www.margaritavillecargo.com/manuals/MANUALS/DM1000-000-000_43_64821634.PDF

Refer to the section on Cleaning and Maintenace; there is a button that needs to be pressed.

Sorry someone has not responded sooner.

Posted on Jun 21, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I put the blade on my Ostis PowerMax clippers? I have tried with it on and off with no success. Thank you.


The blade release should be under the heel of the blade, just below where the blade tongue hinges. You normally only need to press it when removing the blade, when snapping the blade shut it is mostly not necessary to push it. They are a bit like a door latch that self lock when closing.

Feb 17, 2015 | Oster PowerMax 2-Speed Clipper Kit

1 Answer

Can you repack the blade bearing on Vitamix Blenders?


On the Vitamix blender models we have here in NZ it is not possible to repack the bearings, you just purchase a new blade assembly complete with bearings and the driving clutch.

Nov 11, 2013 | Vitamix Super 5000 Work Top Blender

1 Answer

Blade on MD95 not spinning


The shaft has probably siezed at the bottom near the blade. The seal can fail and let liquid inside the shaft and gunge it up.
Take the orange handle apart, then unscrew the four steel pins, then pull out the motor. From the blade end, take the screw from the blade and prize it off. Then pull the shaft out from the top and clean it. It may be stuck - push a blunt nail or similar in the bottom to free it. Clean the shaft and solidified debris inside the tube. Then reassemble carefully.

Feb 14, 2012 | Dynamic MD95 Handheld Blender

1 Answer

My K-Tec Champ HP3 is overloading and shutting off after about 5 seconds even with the jar empty or not even on the machine. It just starts up and shuts off (displaying "OVERLOAD" on the...


Remove the 2 screws from the bottom of the base, release the 4 clips on each side and remove the bottom cover.
There is a fan blade attached to the bottom of the motor and a sensor on the side of it that senses the fan blade turning. If the sensor does not sense the fan blade turning, it assumes that the motor is locked up or 'overloaded'.
Check that the fan blade has not come loose from the motor shaft and reattach if necessary. Verify that the sensor is secure in it's housing next to the fan blade.
Reinstall the base cover and verify operation.

Jan 24, 2011 | K-Tec Champ HP3 Work Top Blender

1 Answer

Leaking from around the base of the jug


When you clean your blender there is a rubber washer in between the blades and where they sit and the glass. Try pushing the blade assembly through the bottom and locate the large washer. Peal it off carefully under warm water then either try to replace it or clean it carefully in soapy dish water. Let me know if this helps, OK?
Jud

Sep 20, 2010 | Russell Hobbs 3902US Work Top Blender

1 Answer

Motor runs but the blade does not spin


The shaft has probably siezed at the bottom near the blade. The seal can fail and let liquid inside the shaft and gunge it up.
Take the orange handle apart, then unscrew the four steel pins, then pull out the motor. From the blade end, take the screw from the blade and prize it off. Then pull the shaft out from the top and clean it. It may be stuck - push a blunt nail or similar in the bottom to free it. Then reassemble carefully

Dec 04, 2009 | Dynamic MD95 Handheld Blender

1 Answer

Braun 4169 disassembly procedure


4169 blender dismantling. this device is not suitable to be dismantled but this is how I did it. 1 disconnect from the mains. 2 lever off operating lever button at opposite end to hinge 3 insert sharp screwdriver into gap by top lid at same side as cable entry and prise off 4 heat up the casing with an electric paint stripper, wear gardening gloves. 5 when the casing starts to get pliable, insert a driver into the gap above the operating button locating lip and prise away as far as you can 6 do this with the locating peg on the other side 7 work between the two until the whole thing comes apart 8 lever out the motor, it will slide out once loosened 9 wash out the blender drive shaft with boiling water and detergent 10 dry out the body and soak the inside with silicone oil 11 work the blender blade until it spins freely 12 clean everything up and push it all back together 13 if any parts are deformed with the heat gun reheat them to a pliable state and reform them as best you can 14 if it is all loose when its back together, glue the joints with superglue and spray with glue accelerator 15 test it and if it's no good chuck it in the bin and buy a new one 16 but mine works fine.

Oct 09, 2009 | Robot Coupe MP450 Handheld Blender

1 Answer

Motor works but blade not spinning


Check and make sure that the shaft in the base housing spins. If it does, the blade assembly has become disconnected from it's shaft probably due to an improper spot weld or peening of the blades to the shaft, or has torn loose or ripped the splines out due to an immovable object trying to be spun. A jammed ice cube can do this. Blade assemblies can be had usually directly through the manufacturer and usually on line. If this has helped, please rate it accordingly.

Jul 20, 2009 | Westinghouse 0101 IntelliBLEND¿ Work...

Not finding what you are looking for?
Margaritaville Frozen Concoction (DM1000) Blender Logo

Related Topics:

394 people viewed this question

Ask a Question

Usually answered in minutes!

Top Margaritaville Blenders Experts

yadayada
yadayada

Level 3 Expert

78257 Answers

john h

Level 3 Expert

12744 Answers

Tom Chichester

Level 3 Expert

41701 Answers

Are you a Margaritaville Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...