Question about Washing Machines

1 Answer

My GE Profile washer top load makes a Pulse / thump and an surge in the lights in the house when the spin cycle kicks in and then it stops spinning. I un loaded the unit and reset and it ran fine without anything in it. But then ran a rince only and it did it again. The unit is only 5 yrs old and I would love to repair it if possible. Any ideas of what to check and where to get a parts breakdown for this unit ? Thanks for your Help.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 487 Answers

Check the bearings and the parts you can get at parts direct from sears

Posted on Apr 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Make a humming noise and spins very slowly


MINE DOES THE SAME. HOUSING IS CRACKED THAT ATTATCHES TO DRUM. WHITE METAL CANNOT BE REPAIRED.

Jul 25, 2010 | GE WPXH214A Front Load Washer

1 Answer

GE top load Profile washer. Spin cycle not


Hi,
If you are having a problem with your top load washer then check out this tip...

Washing Machine2_bing.gif does not Pump or Spin
http://www.fixya.com/support/r4617986-washing_machine_not_pump_or_spin

If you are having problems with your front load washing machine2_bing.gif then checkout this tip...

Front Load Washing Machine2_bing.gif not draining and or not spinning
http://www.fixya.com/support/r4784376-front_load_washing_machine_not_draining

heatman101

Jun 11, 2010 | GE WVSR1060A Top Load Washer

1 Answer

There is power to the washer, water will drain


Try unplugging machine for 30 seconds then plug back in then lift and close the lid 5 times which will reset the motor. Try the spin cycle if it works you may have had a power surge which took the motor out and just needed reset. If it fails you may have a bad inline fuse or motor.

Feb 26, 2010 | GE Profile WPRE6100G Top Load Washer

1 Answer

Loud thumping while stopping after spin cycle.


make sure the shiping rod is out it will do that if it,s not out

May 29, 2009 | Kenmore 22422 Top Load Washer

1 Answer

Loud noise when aggitating code says motor not rotating properly


It's noisy Most noises from a washing machine occur during the spin cycle. If you hear loud thumping during the spin, the load of clothes may have become unbalanced. Stop the washer and redistribute the clothes, then re-start it. Repeat these steps if necessary.
or something stuck up in spinning motor assembly.

thanks and plse do not forget to accept the solution.

Apr 02, 2009 | GE Profile Harmony WPGT9360E 4.0 Cu. Ft....

1 Answer

Loud clicking/thumping in rinse and spin cycle


It doesn't look like a motor problem !!! It seems like an unbalanced tub issue. The machin has suspension dampers and suspension rods, and it's look like one of them was damaged or "run away" from its location during machin's movement. Goog luck !!

Jun 14, 2006 | GE Profile Prodigy WPSE4200A

2 Answers

Washer makes loud thumping after finished spin cycle


I replaced the drive block and it solved my problem. (thumping noise at the end of spin cycle) Easy repair. Videos on utube show all the steps.

Jun 07, 2006 | Whirlpool LSR7333 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...