Question about Sony FD Trinitron WEGA KV-27HS420 27" TV

Open Question

Pls tell me sony ctv dz29-m61 problem is pincution pictures coming but big width too much and after few second tv is off and after led blinking two times what is the problem

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
jupits69
  • 4 Answers

SOURCE: KV HR36 Sony Wega, 10 blink and turn off...

try to replace the horizontal out transistor

Posted on Jul 18, 2008

Ad
VOTIT
  • 2071 Answers

SOURCE: Sony TV

Here is a list of the problems that might have occurred indicated by the number of blinks. The words in parentheses are those, which you will see for each of these faults on a diagnosis screen described later in this article.

  • Unit is dead, No blinks - Problem in the standby power section. Might check fuse, R607, Q601, IC601, R612 and VDR601 (should show open).
  • Continuous blink once a second, no pausing - No reply from the jungle IC301 (data bus is busy, shorted to ground, or held high), IK video path is defective.
  • One blink - not used for the self-diagnosis
  • Two blinks - B+ over current protection (OCP), unit goes to the standby mode then displays the 2 blink fault. Could be a short in the power supply of any of the circuits.
  • Three blinks - B+ over voltage protection (OVP), unit goes to the standby mode then displays the 3 blink fault. This is also a problem in the power supply circuit, check T603 and R672.
  • Four blinks - No vertical Deflection (V STOP), Screen goes to a single horizontal line then the video signal muted. Check IC1509, Q1505
  • Five blinks - AKB circuit (automatic kine bias), the timer/standby indicator blinks for about 30 seconds then goes to the self-diagnosis function. Something is wrong with the video. Check video out, Q705, 732, 761 and other components on the C board, also check Q218, 219, 220 on the A board. In addition, unit could be in IK blanking, try turning up screen slightly.
  • Six blinks - No Horizontal (H STOP), no raster, goes to the blinking self-diagnosis function immediately. Check C515 & 516 and the jungle IC, IC206.
  • Seven blinks - High voltage shutdown. The high voltage has exceeded 33k and the unit goes immediately into safety shutdown. Check power supply regulation and horizontal circuits.
  • Eight blinks - Problem with the audio (AUDIO), unit goes to standby and blinks the self-diagnosis code. Check IC406 audio amp, PS401, and 402. On some projection models of Sony TV sets, this code means that T8005 (flyback transformer), or the associative components in the high voltage circuits are defective on the D board.

  • Nine blinks - Replace D 6116 and D 6301 on the "G" board, do not resolder as this will fix the problem temporary. Or Panel Module Error or Thermal Error. If it is intermittent 9 blinks, meaning sometimes the TV comes on and other times you get flashing, then change the switching regulator on the "G" board or check connections. Make sure the regulator is -12 or -13 (negitive).
  • Ten blinks - Check Q8014 and Q8013 for shorts, leakage, or bad solder connections on the " D" board. If the transistors are bad, check R8051 and IC8005, also on the "D" board.
Intermittent problems? This is a great feature. You can also bring up these fault codes on-screen to see a list of the problem numbers with the abbreviation of the problem and the number of times this problem has occurred. This is slightly different than entering the service mode. To see the diagnostic screen, press the following buttons: Display, Channel, 5, volume Minus, ( not plus ) then Power. This brings up a screen with a list of the problems and number of times they have occurred. Each of the problems named, are abbreviated as, "OCP", "OVP", "V STOP", ETC. We have repeated them in parentheses in the text for the "Blinks" described above so you can correlate between the diagnostic screen and the blink codes.
Now that you know about these self-diagnostics, how do you use them? Say that you have a set with a black screen. You see that the LED is blinking four times. This would tell you that you have no vertical sweep, which is why the video is muted. If it was blinking 6 times, you would know that you have a horizontal fault. It's not a sure cure..
IMPORTANT: After you repair the unit, you MUST clear the values on this diagnostic screen. These codes do not reset themselves after the fault is corrected, so if you don't clear them, you'll be seeing "old" fault codes the next time you enter this screen. Clearing is done by going into the service mode (display, channel, 5, volume plus, then power ). Press 8 and Enter,

Hope this may help;

Regards,
VOTIT

Posted on Aug 30, 2008

welcomejee
  • 10594 Answers

SOURCE: Sony Vega Service Codes

KV-32HS510 and KV-27HS420, seven times blink error code shows problem in Horizontal deflection circuit.

There are many possibilities like dry solder joints, weak capacitors, Horizontal transistor short or flyback transformer fried etc.

If you have little experience of TV repair and good solder skills and have necessary tools to test / check defective parts, then you can make it. you also need to have related service manual to see board location, schematics and part numbers.


Posted on Dec 12, 2008

sodeep
  • 3267 Answers

SOURCE: I have sony 29'' crt

2 blinks means - over current protection (OCP) , unit goes to the standby
mode then displays the 2 blink fault. Could be a short in the power supply of
any of the circuits.

Posted on Jun 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Five red blinks in Sony LED TV KDL 40W900A.


5 red flashes is a bad panel connection or internal panel short, very carefully take the panel connectors off and reseat them and see if that helps, unfortunately you may have a bad panel.

Oct 14, 2017 | Sony Televison & Video

1 Answer

TV Sony sound but no picture


Hello
Check the horizontal output section. Check the LOYT [Line Output Transformer]

Mar 09, 2012 | Sony Televison & Video

1 Answer

I have " Sony FD Trinitron WEGA KV-36HS420 36" TV


U have a soldering iron,desoldering pump or a roll of desoldering braids,a roll of solders?Can u do basic soldering and uderstand basic electronic?FBT- the flyback transformer,the big black block of a plastic with a red wire with a cap hook to a CRT-tv picture tube.Near the big block of a plastic with a red wire with a cap hook to a CRT picture tube.Inside to the right of the FBT,there are 2 power supply ICS,those 2 ICS are dead.Replaced these 2 power supply ICS near the FBT,will solved this tv LED power light indication blinking and will have stable tv power again,and tv will work.

Nov 29, 2010 | Sony FD Trinitron WEGA KV-36HS420 36" TV

1 Answer

I have a Sony ' Wega " about 6 years old 36 HD.. I turned it on and the stand by light blinks NO PICTURE.. OR SOUND AT FIRST IT MADE SOUND AND I THOUGHT PICTURE WAS GOING TO GO ON IT SHUT OFF...CAN YOU...


Please intimate exact model of Sony TV and how many times LED blinks as there would be 3 second pause between blinks so count blinks and let me know. This LED blink is an error code that will tell me problem section in TV.
Thanks.

Sep 07, 2009 | Sony Televison & Video

1 Answer

Sony Grand WEGA KF-50WE610 LED blinks 4 times


Hi,
4 times blink shows Temp Error and requires temperature sensor replacement in Sony KF-50WE610 TV

May 21, 2009 | Sony Grand WEGA KF50WE610 50" Rear...

1 Answer

Sound but no picture


hi
i think its a colour wheel problem...if there is led blink tell me how many times it will blink i will sort if there is error code and i will tell the solution

Feb 14, 2009 | Sony Televison & Video

1 Answer

Repair inquiry


Hi,
     According to the LED BLINKING there must be some problem that are given below:

Diagnosis item:  Video out abnormality detection

TIMER/STANDBY
Indicater
Number of blinks:  
5 times


Supposed malfunction:  Video out, IC7101, 7201, 7301 and others in C board circuit.
Q510,516,524 (A board)

Condition:TIMER/STANDBY LED blinks approx. 30 seconds,
and then blinks for the self diagnosis.

Self-diagnosis
screen display,
Diagnosis item: Results:   5 : AKB 000


So, This was the result of 5 times led blinking.I would suggest you to please contact any expert or strongly recommend to contact any SONY SERVICE CENTRE for repair because it's not an easy job to rectify this problem. Hope you better understand my sayings.

Thank you for using fixya.

 
                                 
                              


Nov 29, 2008 | Sony KP-53HS10 TV

1 Answer

KP-46S4U lose picture after a few second blink of brightness


does the from led blink if so how mant times pause then blink again?

Feb 12, 2008 | Sony KP-48S65 48" Rear Projection...

6 Answers

Sony KP-FX432M91 TV 10 blinks


my sony kp-fx432m91 has a 10 blinks problem. it has no pictures but has sound that goes off after 5 seconds please advice on what to do.

my email address is drbonnyb@yahoo.com

Oct 31, 2007 | Sony KP-FX532M91 TV

Not finding what you are looking for?
Sony FD Trinitron WEGA KV-27HS420 27" TV Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75767 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1689 Answers

Are you a Sony Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...