Question about BenQ FP731 17" LCD Monitor

1 Answer

Our power was just off for about 30 minutes but when the power came on my monitor is black and the power button is just flashing blue???

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

F you are going to DIY and have proper tools and know safety precaution then please read on:
Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply, blown fuses; poor solder joints, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside.

http://en.wikipedia.org/wiki/Capacitor_plague
http://www.badcaps.net

Replacement board:
http://www.lcdrepair.us

Posted on Jul 19, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why did my computer monitor stop showing an image?


Disconnect it from computer and power. wait 15 minutes and plug only the power back in, press the power on button. The monitor may display a message that there is no signal or something like that. If that happens the problem is either the cable or the computer. If you get no message then look for the menu button and press it to see if any thing appears. If not find the manual on line and read it. Many times monitors get over-driven by computers to the point that they can't display OR they self destruct.


OR

Another way is to just unplug everything computer and monitor for 15 minutes. Plug in monitor first then plug in computer and press the power button, the display should display the booting information if the cable is good and the monitor is good.

Jul 19, 2014 | ViewSonic Computers & Internet

1 Answer

The screen was unplugged and now when plugged in the blue light around the power buton just flashes


I tried the reset procedure, i've left it unplugged now for a week and upon ... Now the fifth died. This time, no illumination, just flashing blue light. ... The screen is completely black, the power button is dark blue and no amount of ... The monitor was gone for about 2 weeks (maybe 3) I left it plugged in and ...
deliverator.silverfir.net/?p=369

Dec 04, 2009 | Samsung SyncMaster 932B LCD Monitor

1 Answer

I have a I-Inc monitor model# CY-199. The power went out and back on after a minute, the monitor was on and working when the power went out, when the power came back on the power button went blue like...


It would be nice if all badcaps are bulged/leaking. Changing the lamps is a pain in the ass, i will try it myself with an 191d. But i have tried first the power supply with multimeter capable of 100kHz AC 200mV range. Better if you borrow an ESR meter capable of in circuit measurement and test all condensators.

Allways discharge, disconnect from pc, switch iMonitor on and pull wall plug, push ON button for safety. My 400V capacitor is then down to 7VDC (germany 230VAC mains). Or wait for 30 min, (i am not patient enough for that).



http://www.badcaps.net

Oct 19, 2009 | Hannstar I-Inc TW-191D Monitor

1 Answer

From a cold start,power on,screen is all blue with "no signal" in the upper right corner. while still in blue screen mode approx 2 minutes after start a squealing sound starts. about 1 minute later the...


Sounds like a power supply fault due to leaky capacitors(electrolitics).
From cold take the back off and run a hair dryer over the power supply for a few minutes then switch on,if it comes up fully working then you have to isolate the faulty part/parts and replace.

Oct 01, 2009 | Polaroid FLM-3732 Television

1 Answer

Gateway monitor FPD1975W won't display


Same problem - unplug both computer and monitor - hold power button for monitor for 15-30 seconds...then power it back on and then power on the computer. Seems from other sites there is a power issue with the monitor - this worked for me.

May 23, 2009 | Gateway FPD1975W 19" LCD Monitor

1 Answer

Digital Power Saving Mode


Go to your monitor power settings and turn off Hibernation and other monitor power schemes.

If this problem persist, request for more technical assistance from the manufacturers website

Nov 30, 2008 | LG W2252TQ Monitor

2 Answers

HP vs17 monitor power button flashes blue but screen stays black.


Try put off Monitor uplug power cord and the VGA cord for 1min and reinsert and restart your PC.

Nov 25, 2008 | HP Vs17 17" LCD Flat Panel Monitor

1 Answer

Screen remains black and flashing blue light on power button


I also have the exact same problem. My monitors been collecting dust for a while now and I can't find the solution anywhere.

Aug 05, 2008 | HP f1905 19" Flat Panel LCD Monitor

1 Answer

Screen flashing differnet colours


My Benq lcd monitor does the same thing.

Sep 17, 2007 | Videoseven R17PS 17" LCD Monitor

Not finding what you are looking for?
BenQ FP731 17" LCD Monitor Logo

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top BenQ Computers & Internet Experts

JP Services
JP Services

Level 2 Expert

310 Answers

Tommmix

Level 1 Expert

6 Answers

Computer Links

Level 3 Expert

2386 Answers

Are you a BenQ Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...