Question about Sharp Aquos LC-32D40U Television

1 Answer

The "Please Wait" screen does not go away

When I turn the TV on, the "Please Wait" screen does not go away.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 7 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bar acroos the screen says video/conmponent 1, will not go away


Try hitting any button on the Tv remote to see if it goes away. If it still there and still says powering on , you may have to wait a few more seconds. If this isn't the answer, try toe prodect website to see if there is an answer to this problem. IF not and it is still under warranty, take it back to the store you bought it from for a replacement or a refund. :-)

Jul 20, 2014 | Sony BRAVIA XBR55HX929 55 Inch 3D 1080p...

1 Answer

My LCD dynex tv will turn on but keeps flashing on and off saying please wait


The fact that Please Wait appears on the screen that the power board is fine. I would unplug the tv for 4 hours and plug it back in to see if the same thing happens. It does appear that you need to replace the main board,

Apr 17, 2014 | Dynex DX-LCD32-09 LCD TV

1 Answer

New installation, can't get anything on the screen except message: power only V.3.08.8


With your set turned on, press exit or return on your LG remote. The white screen should go away and you will still see power only. Now turn off the TV and wait a few seconds. Turn your TV on and you should be in business.

Apr 27, 2011 | LG 42LC2D 42 in. LCD HDTV

1 Answer

My mitsubishi 60 in turns off by its self some times 5 min after you turn it on sometimes 5 hours and sometimes 5 days. you can tell when its about to turn off by line that flash on the screen. then they...


Well if your tv is older like the one in the pic it sounds like the bulb is overheating, you may want to vacuum the dust out of the back and make sure it isn't got block of air flow in the back and also make sure it isn't up against a heat source

Feb 19, 2018 | Mitsubishi VS-60607 TV

1 Answer

'Please wait every couple of minutes'


Have you tried to restart or shut down and turn it back on?

Apr 02, 2010 | Acer Windows Vista TL-562G Notebook

1 Answer

Black box on screen


Use the remote and turn off the closed captioning.Button is Usually maked cc


Please rate this a fixya

Feb 13, 2009 | Sony FD Trinitron WEGA KV-36FS120 36" TV

1 Answer

When i turn my tv on i have a " please wait " message on the screen.


see the link below but first make sure here is no dvd in the drive
because a bad dvd can cause this problem

working on sharp lcd tv dvd combo LC 26DV20UPLEASE WAIT

Jan 02, 2018 | Sharp LC26DV20U 26 in. LCD HDTV/DVD Combo

2 Answers

PLASMA DISPLAY STARTING UP. PLEASE WAIT


Un plug the power to the Plasma Screen and also to the Media Receiver for ten minutes. Disconnect the off the air antennas both A and B. After ten minutes plug in the plasma screen then the media receiver and turn on wi the remote control. You should now be back in operation. I was.
Also It may not be a bad digital tuner. The TV Guide feature is active even when the zip code is set to all 0s so if you have an over the air antenna attached the TV will look for the TV Guide info and if it can not find it because of a weak signal or the chanel it is tuned to does not carry that information the TV thinks that tuner does not work which triggers the 12 flashes. Also on power up the gray box with the waring message "Plasma Display Starting Up, Please Wait" appears and the screen is blank.

Feb 10, 2008 | Pioneer PDP-5060HD 50 in. Plasma...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

445 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75767 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Jaime Hernandez

Level 3 Expert

2336 Answers

Are you a Sharp Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...