Question about Hunter Ceiling Fan Light Switch Control

2 Answers

Hunter fan model 25706 both the lights & fan have stopped working

I have a Hunter fan model 25706 that has both light and fan. The ceiling fan and light both have failed at once. Is there a reset switch on the fan? I have checked and there is electricity going to the fan. If the motor failed why are the lights not working?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hello, I am not an electrician. I know you mentioned electricity is going to the fan and I read the other gentleman's answer if the motor component goes it bares consequence on the light working. It's plausible the motor went causing the light not to work. However I wondered if the wall switch went bad. I would change the wall switch and see if that is the culprit.

Posted on Oct 06, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,970 Answers

Mcdevito75 here, VeryGood question, very good, here we go, ------ First a re-set for the motor, I really don"t know but if there is it"s on the motor itself, you"d have to un-screw the cover just at the ceiling and let this cover slide down the chain Attached from the ceiling to the fan itself. and check the motor itself for a reset swtch, usually a red bitton. Now!! true, if the fan motor is bad it could affect the lights, here"s how, the wall switch supplies electricity to the fan motor and the pull chain on the motor turns the fan on, from the motor itself to the fan lights another wire also from the fan motor goes to the fan lights, SO!! if the fan motor is no good it won"t allow electricity to go on to the fan lights. Maybe you Fan motor is just stuck, specially if you haven"t used it in a whlie, with the wall swiotch on and fan speed on low try to gently move the fan blades them selves. If not you may have to repalace the fan.

Posted on Jul 22, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Hunter fan 27227 remote stopped working


How i fixed my Hunter #28096 remote controlled ceiling fan, started not controlling the light, then later the fan quit also. Start by testing the remote buttons, see this post... Cp9430r Fixya

Jun 22, 2014 | Hunter Ceiling Fan Light Remote Control

1 Answer

I have a Hunter ceiling fan with a remote control model number 85095. The remote will turn the fan on and off and change the speeds but it will not turn the light on or off anymore. Any help?


Make sure the wires to the light kit are connected to the light & light wire connected in ceiling.If that's not your problem then you probably need a new receiver. Call 1-888-830-1326 and have your FAN model handy.Should be a five digit number beginning with a 2.

Jan 14, 2013 | Hunter Ceiling Fan Remote Transmitter...

2 Answers

Hunter ceiling fan fan is working but lights are not


Make sure light wire is connected at the ceiling & at the bottom. Otherwise it's probably the receiver. 1-888-830-1326 ( Hunter parts )

Jan 05, 2013 | Hunter 52" Ceiling Fan With Light And...

1 Answer

I have a hunter ceiling fan and the light blew, when it blew then the remote quit working for the light, it still turns the fan on & off but after I replaced the bulb it still will not operate the...


Hello nita... I believe the fact that the remote stopped working is due to a weak battery in the remote. Change that battery and you should be back up and running. Joe

Thanks for choosing Fixya!

Jan 14, 2011 | Hunter 20537 / 20538 The Vista Iron...

2 Answers

Light remote control stopped working


most of my fan controls have done this to me. you know the reciever is working cuz the fan works fine. you need to dis assemble the remote completely and clean the contacts for the light button. mine are two small black dots that seem to keep getting slimey and wont work till i clean them, then all works like brand new again.

good luck.

Aug 21, 2009 | Hunter 52" Ceiling Fan With Light And...

1 Answer

Hunter ceiling fan (model no. 25736) and light not starting


Home Depot sells universal remote systems (transmitter and receiver) for around $30 (in Delaware & Pennsylvania) -- don't know price in Chicago).

I'd just replace it. Hunter may be correct that they are the only source for the receiver, but if you get a new transmitter as well, you don't need their receiver. The labor is the same either way.

Charlie

Aug 18, 2009 | Hunter 52" Ceiling Fan With Light And...

Not finding what you are looking for?
Dryers Logo

647 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hunter Dryers Experts

Joe Paxton

Level 1 Expert

8 Answers

Paul Bade

Level 3 Expert

1650 Answers

Craig Butler
Craig Butler

Level 3 Expert

1730 Answers

Are you a Hunter Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...