Question about Kenwood Audio Players & Recorders

1 Answer

KRF-X7775D Problem - NO Sound

My KRF-X7775D Problem is that I'm getting NO sound.

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Same here, see this post. Been trying to contact they guy to figure out what the outcome was for a little while now.

Posted on Jul 17, 2010

Testimonial: "This did not help me"

  • michiamoneo Oct 19, 2010

    Thi is a problem of digital board , thi is a eprom sstoring , you can order to Kenwood assistance

  • He Ze Aug 21, 2012

    Same problem here. Did you be able to fix the problem? Can michiamoneo explain what the problem is and how to fix it? Thanks!



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Sounds ok but not dialogue...

It sounds to me like you are using the receiver in surround sound mode and the click you hear is the center channel turning off. If you have another center channel speaker, try swapping that for the one you are currently using. If that doesn't fix the issue, then try replacing the speaker wire. If that still doesn't fix it, then the issue is probably inside the receiver and may be either an output transistor that is failing when hot or an electrolytic capacitor that allows too much DC offset when hot.

Oct 10, 2016 | Kenwood KRF-V5060D Receiver

1 Answer

I have a kenwood krf-x7775d receiver , but the problem is when i switch off the system or even put it on standby, when i turned it on again there will no sounds comes out from the speaker . What happens is...

try they claim to have driver upgrades for this system. you should have mentioned that this system is a home audio/video thx setup. makes a big difference- at least it did back in the day! b&w, change the channel! adjust the rabbit ears! the horizontal hold\'s screwing up again! think a tube just blew! etc.!!

Nov 04, 2013 | Audio Players & Recorders

1 Answer

Hi, my speakers are starting to sound a bit weird and i think its cause of pplaying around with the equalizers and settings on the Kenwood Amplifier, am just wondering if there is a reset button to restore...

Why guess? Get the manual out and actually look at the settings to see if they're out in space somewhere. If you don't try to understand what went wrong you will repeat it.

Register and download the manual for free at

Page 33 if you want the shortcut to factory settings.

Mar 24, 2011 | Kenwood KRF-V5060D Receiver

1 Answer

My surround sound system is making intermittent thumping noises. It used to only do it when we shut it off, a few minutes later it would thump a few times. Now, it is doing it when its on. Why is it doing...

I had the same problem with my Kenwood KRF 5060d
First just sometimes I used to hear this noise click clack from the device while the sound disappeared. Then the problem became more frequent and no mere bearable.

So I've tryed to restablish the weldings on the board in correspondence to the speakers connections and the relay connections. Nothing changed, so I've substituted the relay OMRON G5PA 28 NW 12VDC 2 contacts normally open (6 pins) with the new FINDER 40.52 (8 pins) letting free the 2 pins for the normally close contacts.

Now my KRF 5060d is working properly with the only problem that sometimes the dispaly disappear and I have to apply a little pression on it with my fingers in order switch it on. Maybe I've compromised some contacts in the frontal pannel while unmounting even if it wasn't necessary.


Oct 19, 2010 | Kenwood KRF-V5060D Receiver

1 Answer

Music, sound effects no dialogue


May 14, 2009 | Kenwood KRF-V5060D Receiver

2 Answers

Unable to get sound from tv to output from surround sound

as the tv stations that were being feed into the system were digital and the nput was actually analgoue 2 optical cables are required.
have tv sound and blue ray sound through surround sound when tv channels were changed to analague.

Mar 22, 2009 | Kenwood Audio Players & Recorders

1 Answer

Krf 5030 sound off and on

it sounds like the power amp needs to be replaced , it will eventually quit

Dec 09, 2008 | Kenwood KRF-V5060D Receiver

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

699 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Audio Players & Recorders Experts


Level 3 Expert

5309 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Don Hart

Level 2 Expert

108 Answers

Are you a Kenwood Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides