Question about Canon PIXMA iP3300 InkJet Photo Printer

1 Answer

Paper jam error message

The warning light is flashing to indicate there is a 'paper jam' and an error message appears on my screen stating the same! I have checked and there is no paper jammed and the printer is quite new and has never had any paper caught up in it!!
Help!

Posted by on

  • tarajosey Jul 07, 2008

    my printer says there is a paper jam, ive checked it throughly, and there is no paper jam, yet the orange light still flashed indicating there is a paper jam, the printer is fairly new, and ive never had any problems up until now,
    please help!

  • Anonymous Mar 28, 2014

    I turn it off then when i turn on an error appeared paper jam

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Expert
  • 377 Answers

Hi dear

this the error code
E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error
E2-2 No paper (ASF)
E3-3 Paper jam
E4 No ink
E5-5 The ink cartridges are not installed or a non-supported ink cartridge is installed ,
or the ink cartridges are not installed properly
E8 Waste ink absorber full, or platen waste ink absorber full




First, download the software at http://www.box.net/shared/4yblbn34kg

Secondly, to run the software your printer has to be in service mode. Do that by
- unplug cable
- press and hold "power" button
- plug cable
- press "resume" and release
- release the "power" button
At this stage, your computer will detect a new hardware

Run the software.

oke

Posted on Apr 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My printer is blinking green light in every 5 seconds. i am give test print but is not came to print




Ready and Error Lights (EPL-6200L only)
The Ready (green) and Error (red) lights on the top of the printer may be the first indication of trouble. The status of the lights, on, off or flashing, indicates your printer status, as described below. The Status Alert window in the EPSON Status Monitor 3 utility indicates what type of error has occurred and offers you a possible solution. Look through this section to find the kind of problem you have, then try the recommended solutions in the order they are presented until your problem is solved.
>
a. Error light (red)
b. Ready light (green)

Status/Error/Warning
INDICATOR LIGHTS
Ready
Error
Service Required (controller error)
OFF
> Service Required (engine error)
> > Service Required (protocol error)
> > Output Paper Jam
> > Paper Jam
> > Paper Out/Feed Jam
> > No Developer Cartridge Installed
> > Wrong Developer Cartridge Installed
> > Installed Developer Cartridge is Not a Genuine EPSON Product
> > Developer Cartridge Memory Error
> > Toner Out
> > Front Cover Open
> > Output Cover Open
> > Printing on Incorrect Paper Size
> > Unsupported Paper Size
> > Time Out Error
> > Insufficient Memory to Print Current Page
> > Paper Size Warning
> OFF
Not All Pages Are Printed
> OFF
Warming Up
> OFF
Replace Photoconductor Unit
> OFF
Toner Low
> OFF
Installed Developer Cartridge is Not a Genuine EPSON Product Warning
> OFF
Sleep mode
> OFF
Ready
> OFF
Printing
> OFF
Processing Data
> OFF
> Note: > If the problem remains after trying the suggestions in this section, contact your dealer or a qualified service representative for assistance.

Service Required (controller error)

Control panel: Error light on
A controller error has been detected. Turn off the printer, wait 5 seconds and then turn it back on. If all the lights come on again, turn off the printer, unplug the power cord, and contact a qualified service representative.

Service Required (engine error)

Control panel: Ready and Error lights flashing
A print engine error has been detected. Turn off the printer, wait 5 seconds and then turn it back on. If the lights come on again, turn off the printer, unplug the power cord, and contact a qualified service representative.

Service Required (protocol error)

Control panel: Ready light flashing, Error light on
A protocol error has been detected. Turn off the printer, wait 5 seconds and then turn it back on. If the lights come on again, turn off the printer, unplug the power cord, and contact a qualified service representative.

Output Paper Jam

Control panel: Ready and Error lights on
Indicates that there may be a paper jam inside the printer. Open the printer's output cover, remove any jammed paper, and close the cover. The error will automatically clear itself and the jammed page's print data is reprinted.

Paper Jam

Control panel: Ready and Error lights on
Indicates that there may be a paper jam inside the printer. Open the printer's front cover, remove any jammed paper, and close the cover. The error will automatically clear itself and the jammed page's print data is reprinted.

Paper Out/Feed Jam

Control panel: Ready and Error lights on
Indicates that there is either no paper loaded in the printer, or there is a paper jam in the feed slot.
If no paper is loaded, load paper into the MP tray, then open and close the printer's front cover. See Loading Paper for instructions on loading paper.
You can clear the error by pressing Continue on the EPSON Status Monitor 3 window that appears.
If paper is loaded, then there is a paper jam in the feed slot. See Clearing Jammed Paper for instructions on clearing paper jams. The error is automatically resolved upon clearing the jammed paper and opening and closing the printer's front cover.

No Developer Cartridge Installed

Control panel: Ready and Error lights on
Either the developer cartridge is not installed or is installed incorrectly. Check to see if the developer cartridge is properly installed and follow the instructions under Developer Cartridge to install or reinstall it.

Wrong Developer Cartridge Installed

Control panel: Ready and Error lights on
Either the installed developer cartridge is defective, or it is not the right one for your printer model. Replace it with a new or correct developer cartridge by following the instructions under Developer Cartridge.

Installed Developer Cartridge is Not a Genuine EPSON Product

Control panel: Ready light on, Error light flashing
The installed developer cartridge is not a genuine EPSON product. The use of such products may damage the printer and cause the print quality to decrease. Remove the currently installed cartridge and replace it with a genuine EPSON cartridge by following the instructions under Developer Cartridge.
To continue using the currently installed developer cartridge, press Continue on the EPSON Status Monitor 3 window that appears to clear the error.

Developer Cartridge Memory Error

Control panel: Ready light on, Error light flashing
A memory read/write error has occurred. Try reinstalling the developer cartridge or replacing the current cartridge with a new one by following the instructions under Developer Cartridge. If this still does not resolve the problem, turn the power off and then on again.

Toner Out

Control panel: Ready light on, Error light flashing
The developer cartridge is out of toner. Replace the developer cartridge by following the instructions under Developer Cartridge. To clear this error and print a single sheet, press Continue on the EPSON Status Monitor 3 window that appears to clear the error. After that, this error will occur again until the developer cartridge is replaced. If you set the Toner Out Error setting to Off, you can continue printing even when this error occurs.

Front Cover Open

Control panel: Ready and Error lights on
The printer's front cover is open. Make sure that the printer's front cover is closed properly by opening and closing it again.

Output Cover Open

Control panel: Ready and Error lights on
The printer's output cover is open. Make sure that the printer's output cover is closed properly by opening and closing it again.

Printing on Incorrect Paper Size

Control panel: Ready light on, Error light flashing
The paper loaded in the paper source does not match the required paper size. Replace with paper of the correct size and click Continue on the EPSON Status Monitor 3 window that appears. If you want to change printer driver settings, click Stop.

Unsupported Paper Size

Control panel: Ready light on, Error light flashing
The specified paper size is not supported by this printer, or the paper feed direction is incorrect. To continue printing from the page after the page that caused the error, click Continue on the EPSON Status Monitor 3 window that appears. If you want to change printer driver settings, click Stop.

Time Out Error

Control panel: Ready light on, Error light flashing
Data transmission from the computer to the printer is interrupted and a timeout error has occurred. Click Print Again on the EPSON Status Monitor 3 window that appears to resume printing. If printing does not resume, or if you want to change printer driver settings, click Stop.

Insufficient Memory to Print Current Page

Control panel: Ready light on, Error light flashing
The printer does not have sufficient memory to print the current page. To continue printing from the page after the page that caused the error, click Continue on the EPSON Status Monitor 3 window that appears. If you want to change printer driver settings, click Stop.

Paper Size Warning

Control panel: Ready light on
The size of the paper that fed through the printer does not match the specified paper size. Click Close on the EPSON Status Monitor 3 window that appears to dismiss the warning.

Not All Pages Are Printed

Control panel: Ready light on
This warning is displayed if an Insufficient Memory to Print Current Page error has occurred while Auto Continue is set to On. Click Close on the EPSON Status Monitor 3 window that appears to dismiss the warning.

Warming Up

Control panel: Ready light flashing
Indicates that the printer is warming up to process and print data.

Replace Photoconductor Unit

Control panel: Ready light flashing (flashes at longer intervals than usual)
Indicates that the photoconductor unit is close to the end of its service life (less that 5%). Prepare a new photoconductor unit to replace the current one. See Photoconductor Unit for instructions.
To temporarily dismiss the warning, click Close on the EPSON Status Monitor 3 window that appears. Resetting the photoconductor unit also clears the warning.

Toner Low

Control panel: Ready light flashing (flashes at longer intervals than usual)
Indicates that the developer cartridge is nearly out of toner. Prepare a new developer cartridge to replace the current one. See Developer Cartridge for instructions.

Installed Developer Cartridge is Not a Genuine EPSON Product Warning

Control panel: Ready light flashing (flashes at longer intervals than usual)
This is a warning to inform you that the installed developer cartridge is not a genuine EPSON product. The use of such products may damage the printer and cause the print quality to decrease. Remove the currently installed cartridge and replace it with a genuine EPSON cartridge by following the instructions under Developer Cartridge.
To temporarily dismiss the warning, click Close on the EPSON Status Monitor 3 window that appears.

Sleep mode

Control panel: Ready light on
Indicates that the printer is in energy-saving mode. The printer goes into standby due to inactivity. If the Sleep mode is enabled, the printer goes into standby in 15 minutes.

Ready

Control panel: Ready light on
Indicates that the printer is ready to print.

Printing

Control panel: Ready light flashing
Indicates that the printer is printing data.

Processing Data

Control panel: Ready light flashing
Indicates that the printer is processing data.

Mar 18, 2015 | Epson laser Printer EPL-6200L Laser

1 Answer

Media jam fuser


replace the fuser unit. and replace the transfer roller and belt,

Jan 30, 2014 | Konica Minolta Magicolor 2530 DL Laser...

1 Answer

A warning sign has appeared on the printer, which says: 'Paper is jammed in the printer. Turn off the printer, open the scanner unit, and remove the paper. See your documention'. But There is no paper...


either a sensor broke
or
a small tiny piece of paper is stuck

after removing a jam if the paper tears a small piece of paper can cause the jam error message

Jan 19, 2011 | Office Equipment & Supplies

1 Answer

The orange warning light flashing what can i do to stop it?


check for paper jam if any or p head or cartridge indication for replacement
some symbol my blinking in display for user attention

this also indicate for error in plotter check for display icon and if you find any special icon other than normal screen as earlier, it will give information like paper with X mark ( no paper in tray )or paper jam ( two circle with Z mark )
or may be some screw driver and spanner X mark that can decode to give reason for LED blinking

if you get tool X mark check for ink level box in each row to check error code, its would be 6 numbers of rows and each row may some box
need to check and confirm to verify the error code


Nov 06, 2009 | HP Designjet 110plus nr InkJet Printer

1 Answer

RX 420 PRINTER WONT PRINT AS PAPER JAMMED WARNING KEEPS FLASHING


hi i hope i can help you? remove the cover from the machine and load paper as normal. and watch if the mechanics is sticking or anything that you can see give a clean with wd40clean all rollers check that you are puting in the correct amount off paper.check for loose connections.check for dirt on the switches.

May 04, 2009 | Xerox Phaser 8400 Laser Printer

1 Answer

Hp officejet 6310 all in one problem when I power up


You may need to copy and paste these links into your browser:
Here is a link relating to clearing the paper jam error message:
http://h10025.www1.hp.com/ewfrf/wc/document?lc=en&cc=us&docname=c00743863&dlc=en&product=1119598

Here is a lik on how to do a power reset when all the lights are flashing.
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&docname=c01059445&dlc=en&lc=en&jumpid=reg_R1002_USEN

Joe
Please remember to rate Techs who assist you for free :)

Oct 07, 2008 | HP Officejet 6310 All-In-One InkJet...

1 Answer

Hp psc 1219


dear szaszy
as per your information your printer paper jam sensor is having problem.Please get it serviced

Apr 04, 2008 | Office Equipment & Supplies

1 Answer

Hp psc 1219


try pressing repeatitivly the red cancel button

Apr 16, 2007 | HP PSC 1210v All-In-One InkJet Printer

Not finding what you are looking for?
Canon PIXMA  iP3300 InkJet Photo Printer Logo

361 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

old marine
old marine

Level 3 Expert

1814 Answers

Corne Viljoen

Level 2 Expert

385 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...