Question about Televison & Video

2 Answers

Antsig AP593 universal remote

I have a Antsig AP593 universal remote and I need the code for my Cobolt television.

Posted by on

  • Matthew Irvine Mar 19, 2011

    Thanks for that. I did end up using the manual search. It worked...sort of. The power didn't go off and in fact it changed the channel. It turns out the 'three' button now controls the power, the 'eight' and the 'four' are channel up and down and the 'six' puts the volume up to fifty.

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Not sure if you've decided to throw your remote control away already or not. But try using the manual search code. Basically press "TV" (light blinks once), then press the "Up" channel button and the "up" volume button at the same time (light comes on permanently), then hold down "Power" whilst putting the remote RIGHT IN FRONT of the place where your tv receives signal (usually where you can see a light), and I mean right in front! Hold it down until your tv powers off. Then it should be configured and working. It took me about 1 minute or more for the TV to react and turn off. Then you can check if it turns on again and if the channels are working.

Posted on Mar 18, 2011

  • Matthew Irvine Mar 19, 2011

    Thanks for that. I did end up using the manual search. It worked...sort of. Now the 'three' button controls the power, the 'four' and the 'eight' are channel up and down, and the 'six' puts the volume up to fifty.

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I have just bought the 6 in 1 universal remote AP592 and all I need to know is how to set it up to control my set top box? There are no buttons for the set top on the control but it states on the box that it can control a set top box.
Thanks

Posted on Jun 01, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the code for a Samsung blue ray DVD on a antsig universal remote


The code is in the antsig remote control if it is compatible. Use code search to find out. If a search through all codes stored in the remote control fails, you may have to try a different universal remote control. All universal remote controls do not contain all possible codes.

Jun 15, 2017 | Samsung Televison & Video

3 Answers

Cobolt 3 in 1 jumbo remote control


have u checked wether is is supported or not????
it may not be supported.............

Sep 18, 2008 | Televison & Video

1 Answer

Remote control codes


028,026,022,020. Try these codes. If you wish to get more codes and other details check:
http://electrohelponline.blogspot.com/
http://electro-medical.blogspot.com/
Both the sites have setup code list, and setup procedure to many popular brand remote controls. Check the site in 'Mosaic' view. It will make search easy.

Jan 07, 2014 | Televison & Video

1 Answer

Antsig AP593 Universal Remote Control Code for Sanyo LCD-40XR10F LCD TV


Hello
Try these codes.
004/ 013/ 049/ 108/ 110/ 180/ 209
0049 0097 0110 0004 0268 0012 0108 0180
Direct Code Entry
  1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
  3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
  4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.

Mar 09, 2012 | Televison & Video

1 Answer

I am trying to use an ANTSIG AP593 Universal Remote Control on a Base DV-360 DVD player, I cannot find a code to use for my DVD player. Can you please tell me a different brand that will either work for my...


This has been answered before on FIXYA. Use the manual search code. Press "TV" (light blinks once), then press the "Up" channel button and the "up" volume button at the same time (light should come on), then hold down "Power" while aiming the remote at your TV. Hold it down until your tv powers off. Then it should be configured and working.It may take several seconds. Then check if it turns on again and if the channels are working.

Feb 02, 2018 | Televison & Video

1 Answer

I lost my lg plasma tv remote i brought antsig universal remote i need the code


These codes work on a LG 4750 with a Comcast three device Remote 11265, 10178, 10700, 10856, 11178, 11758, 11993
1346 ,0008 ,1346




Give credit to adreescheema@yahoo.com
contact No:00923015545637

May 27, 2011 | Televison & Video

1 Answer

I have an ANTSIG AP593 and a BUSH tv I cant get it to tune in....I have tried for two days both the manual and code methods ( a and b).


I used the B method and it worked. But the trick is to really hold the remote right in front..like 1mm away from the point where your tv gets its signal. So wherever you see a light! Took me about 1 minute or more.

Feb 28, 2011 | Televison & Video

1 Answer

I have an antsig AP593 universal remote, i need the code for a toshiba television.


I'm not sure if any of the codes work! But if you want to try the codes again. Put your remote right in front of the point where your TV receives signal (i.e. where you see a light). I used method B - manual searching of the code. Basically press "TV" (light blinks once), then press the "Up" channel button and the "up" volume button at the same time (light comes on permanently), then hold down "Power" whilst putting the remote RIGHT IN FRONT of the place where your tv receives signal (usually where you can see a light), about 1mm away kinda thing! Hold it down until your tv powers off. Then it should be configured and working. It took me about 1 minute or more for the TV to react and turn off. Then you can check if it turns on again and if the channels are working.

Jan 02, 2011 | Televison & Video

3 Answers

Universal remote codes for cobolt tv


0698 - It's about than 40 codes in if you are searching manually.

Aug 29, 2008 | Universal Remote Control Remote Control

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

3,603 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75404 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Cindy Wells

Level 3 Expert

5417 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...