Question about Televison & Video

1 Answer

I have a TX-32PG50 TV, the stand-by light comes on but I cannot select a channel. There is a ticking noise when I select a channel it seems to be comming from the area of the HT transformer after a few seconds it stops and the TV goes back into stand-by.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 319 Answers

Sounds like unit is in protect mode. Have check out by pro/tech

Posted on Apr 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sony KP-57WV700


Hi. It seems that the g2 voltage of the picture tube is too high, resulting in a white screen, often with white horizontal lines. The g2 (= second grid) voltage is derived from the flyback high voltage. The voltage divider is mostly integrated in the flyback trafo housing.(including the adjustment knobs). A failure in this divider may lead to this defect. The static you hear may come from sparking in the divider. The flyback trafo is soldered onto the main printed cirrcuit board. Sometimes, one of the pins sits loose in the soldering pads.
Turn on the set and observe for any sparking around the entire flyback circuitry, and, or the flyback trafo itself
The screen turns black after a while, as a too high beamcurrent is detected. The set disables the flyback. Stand-by blinks meaning that there is a fault condition.
Be carefull with the high voltages. The flyback voltage is very high (20-30 Kilovolts !) and may be lethal !!

Jul 02, 2012 | Sony KP-57WV600 57" Rear Projection...

1 Answer

There is no picture and there is a tick tick ticking noise coming from inside the TV


The ticdk tick sound is probably the switched mode power supply making noise due to the fact that there is a shorted component inside(may be the horiz. output transistor). You may need to have service personell look at unit and get an estimate...this is older set n may not be worth repair

Jan 14, 2011 | Panasonic PT-51HX40 51" Rear Projection...

1 Answer

I have a ticking noise when i try to turn on the tv..


Try putting on the back piece. Some of these TVs have a circuit protection system that will not deactivate with the back open. (It is like an old circuit breaker with the fuse out.)

I hope this helps.

Cindy Wells

Jun 03, 2010 | Philips 50PL9126D/37B 50" DLP TV

1 Answer

WHEN I PLUG IN TV THE TIMER LIGHT IN THE FRONT COMES ON BUT THE SCREEN WONT COME ON AND I CAN HEAR A TICKING NOISE


the ticking comes from overcurrent circuit protection there are several areas inside the tv that could be causing this. The most common are the horizontal drive and output circuit and the power supply. If you call your area service tech he can give you a good idea on what the repair costs will run.

Sep 25, 2009 | Akai PT5492S 54" Rear Projection...

1 Answer

TV WONT TURN ON, STAND BY LIGHT FLASHING 3 TIMES CONTINUOUSLY


i have a toshiba dlp doing that after research i found it to need a lamp replacement

Feb 01, 2009 | Toshiba TheaterWide 46HM84 46" Rear...

1 Answer

Tv won't stay on


Hello mrscarpenter,

This is a common problem with the ITC222 chassis, I would check CP120, CP140, CP150 to see if they are bad I suspect CP150 is the one that is bad. Its value is 2200uf 16VDC. It is located on the same board as the IHVT and is in between the Heat sink in the middle of the board.

I hope this helps,

Shuttle83

http://www.electron-age-technologies-llc.com

Dec 04, 2008 | RCA D52W20 52" Rear Projection HDTV-Ready...

1 Answer

Green flashing power light and ticking noise but wont turn on


Did you touch the Lamp? If you did it may have blown. the color wheel may be the problem or yes the balist

Jul 25, 2008 | Panasonic PT-45LC12 45" Rear Projection...

1 Answer

Ticking noise from TV - Sony 50' rear projection 1080p LCD


The problem is ht leakage . remove the ultar cap of the tube and clean both the tube and cap with wd 40. then reinstall cap using some silicon glue.
this will correct your fault.

Jul 11, 2008 | Sony Grand WEGA KDF-60WF655 60" Rear...

2 Answers

RCA, rear prjetion, 46" tv,no power, ticking sound


Ticking is usually related to the horizontal output and the flyback with the flyback being more suspect. If you need more assistance please let me know

May 13, 2008 | Televison & Video

1 Answer

Will not come on


Sounds like a problem with the stand by votages. Possibly a low voltage regulator. Is the model number a 43H70?

May 03, 2008 | Toshiba 43H70 43" Rear Projection...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69878 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6445 Answers

yadayada
yadayada

Level 3 Expert

64052 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...