Question about Fisher and Paykel GWL11 Top Load Washer

1 Answer

Fisher and Paykel GW612 - Lights showing

Fisher and Paykel GW612 washing machine - Lights showing
x0000 0x0. Help please!

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Fisher and P... Master
  • 713 Answers

Hi just read your posting.The fault on your machine is called Single Rotor Position Sensor Error.The rotor sensor is attached to your motor which is located underneath the machine.Now the Error Code will come up on your machine because 1--The wiring to the Rotor Sensor is faulty. 2-- The rotor sensor itself is faulty or 3--- The motor controller, 'which is located under the top panel is faulty.Unfortunately to test the rotor sensor you need an RPS tester .This device will also check the wiring to the rotor sensor.If you have an electrical test meter I can guide you throe the testing of the wires to the rotor sensor but without the RPS tester you cant accurately test the rotor sensor.Some service techs I know just change the rotor sensor to see if that rectifies the fault but in your case you dont have a rotor sensor so even if you do purchase one and change it, the fault could be your Motor Controller.My best advice to you would be to borrow an electrical test meter if you do not have one and reply back and I can help you eliminate the Wiring as the cause of the fault,and then contact a service tech to find out if the fault is with the Rotor Sensor or the Motor Controller.But if the fault is with the wiring then I can guide you throe step by step to repair it.I hope this helps and please reply on how you got on or if you need further assistance.Good luck.

Posted on Jul 17, 2010

  • tccack Jun 24, 2012

    Can you explain how to get to the RPS on the GW612 F&P. I have this problem also. I have looked under the machine and found the pump out motor (easily removed) but how do I get to the RPS to check it for obvious defects like broken wires etc?

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi I have a F & P washing machine GW612. It has the seventh light come up in diagnostic mode. Is that error 2 & how do i fix it please? Thanks


Here is the instructions manual which contains the detailed diagnostic code explanations from p.33 on.

http://laundry.manualsonline.com/manuals/mfg/fisher_paykel/gw612.html

Aug 26, 2015 | Fisher and Paykel Washing Machines

2 Answers

Need to do a reset on a gw612 after changing the cold valve


There is no reset for these.
If you are getting error code 48,49,50
your motor controller board is faulty.

Feb 21, 2014 | Fisher and Paykel Fisher & Paykel Washer

1 Answer

Gw612 error code lights


the motor controller needs replacing. this fault is not servicable at home.

Sep 07, 2013 | Fisher and Paykel Fisher & Paykel Washer

1 Answer

Fisher & paykel gw612 washer constantly trying to drain


The pump triacc in the motor control board needs to be replaced
by a technician, it's cheaper than getting a new board.

Apr 22, 2013 | Fisher and Paykel Fisher & Paykel Washer

1 Answer

Hi I have a gw612 Fyscher and Paykel 8 years old. It is now refusing to start and the led lights when I turn it on are the third and the fourth wash cycle lights as well as the spin light. If I press start...


Hi just read your posting.Starting from the left to right if the lights that are on when the machine is beeping are the 3rd and 4th and 8th then the error code is called COLD VALVE FAULTY.This means either your cold water valve is faulty or you control module is faulty.Would you like me to guide you in the testing and isolating the fault and replacing the faulty component?Please reply for further help.Looking forward to your reply.

Oct 11, 2010 | Fisher and Paykel Fisher & Paykel Washer

1 Answer

Tub fills but there is no aggitation model gw612


Hi just read your posting,Now, does the machine show an ERROR CODE and beeps?If it does show an error code it will be in a number in your LCD DISPLAY if you have that model or a series of lights will light up.Now these lights will be in a row of 8 lights.Starting from the left to the right which ones are lit when the machine beeps?Is it the 2nd and 4th or the 1st and 5th ---etc---?Please reply with additional information and I am sure I can help you.

Aug 24, 2010 | Fisher and Paykel Fisher & Paykel Washer

1 Answer

Fault code 00XX000X on GW612 washer


Hi just read your posting.This fault code indicates you have a COLD WATER VALVE FAULT.The lights you marked with --x-- are the ones that are lit.Is this correct?What you need to do is to test the valve coil for OHMS resistance.It should be around 60 to 63 ohms.The water valves are located under the top panel.Please reply to tell me how you got on or if you need further assistance.

Jun 26, 2010 | Fisher and Paykel Fisher Paykel Intuitive...

1 Answer

Fisher and paykel gw612 fault 0000X0X0 can any one help X is light on on control board


click on this link directly to get the user manual of your product http://safemanuals.com/user-guide-instructions-owner-manual/FISHER%20%2526%20PAYKEL/GW612%20-_E in this link there is mentioned all types of troubleshooting and error code list. This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

Dec 30, 2009 | Fisher and Paykel Washing Machines

Not finding what you are looking for?
Fisher and Paykel GWL11 Top Load Washer Logo

777 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

michael_t919

Level 2 Expert

88 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...