Question about Televison & Video

3 Answers

Replaced XD300U projector lamp. Need to know how to reset lamp timer. Won,t turn on because lamp timer has expired to 0. Needs to be reset. Lost our manual. Please help.

Posted by on

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 264 Answers

Hi,

I have provided you the link below where you can find the manual for your model and all the steps have been mentioned clearly.

http://www.mitsubishielectric.ca/projectors/pdf/manual_XD300.pdf

Hope this resolves the issue you are facing.

All the Best

Posted on Apr 21, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 123 Answers

How to reset the operation time meter
Plug in the power cord, turn on the main power
switch, and reset lamp time by pressing the VIDEO
button and ENTER button for 3 seconds simultaneously.
• Make sure that the STATUS indicator flashed
twice and the operation time meter has been
reset.
Caution:
• Do not spill liquid on the lamp or place it near
flammable objects or where children can touch it.
Otherwise, it could cause injury or fire.
• Be sure that the projector guide is firmly inserted
between the right and left lamp guides.
Important:
• The projector will not turn on if you do not secure
the lamp lid.
• You must reset the operation time meter after
you replace the lamp.
• Do not reset the operation time meter unless the
lamp has been replaced.

Posted on Apr 21, 2008

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 790 Answers

Hello,

"Reset the lamp counter
i. Press and hold Exit on the projector
for 3 seconds to display the total used
lamp time.
ii. Press Menu on the projector or on
the remote control to access the lamp
hour timer. An adjustment message
will appear.
iii. Press or to reset lamp hours
and press EXIT to leave."

Posted on Apr 21, 2008

  • Kanth raj
    Kanth raj Apr 21, 2008

    HEy for mitsubishi its diff i guess try this..

    lug in the power cord, switch on the projector, and reset lamp time by pressing the left-right POWER buttons simultaneously.

    Caution:


    1. Do not spill liquid on the lamp or place it near flammable objects
      or where children can touch it. Otherwise, it could cause injury or
      fire.

    2. Be sure that the projector guide is firmly inserted between the right and left lamp guides.

    Important:


    1. If the 3 buttons was not pressed at the same time,the lamp time may not be reset.

    2. Please confirm the TEMP indicator illuminates about 2 seconds and the lamp time has been reset.

    3. The projector will not turn on if you do not secure the lamp lid.

    4. You must reset the operation time meter after you replace the lamp.

    5. Do not reset the operation time meter unless the lamp has been replaced.

  • Kanth raj
    Kanth raj Apr 21, 2008

    Hey littlesheila,

    I dint copy ur solution i just got the sam procedure in the below link!!
    http://slayo.com/resetting-the-operation...

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reset lamp timer on epson 5500c after timer has expired


Could be a bad ballast. Did you get the door and latch closed completly?

Apr 26, 2012 | Epson Powerlite 5500c - Lcd Projector -...

1 Answer

Can i reset the lamp timer before the lamp goes out on my Mitsubishi XD300?


How are you resetting them when the timer goes off? Should be the same button pattern. You might have to do it right after or while you plug the machine in.

Jan 14, 2012 | Mitsubishi XD300U Multimedia Projector

2 Answers

Replaced main bulb in front but lamp button on front of tv is still blinking and tv won't show picture


The lamp timer on the Hitachi projector must be reset whenever the lamp has been replaced. The "Lamp" indicator on the display will light red or the "Change the Lamp" message will display when the lamp timer needs to be reset. Hitachi recommends that the lamp timer never be reset without replacing the lamp and to always reset the timer when the lamp is replaced. The message functions of the projector will not function properly if the lamp timer is not correctly reset.

  • Turn the power on. Press the "Reset" button for three seconds until the "Lamp xxxx hr" message appears on the lamp timer on the bottom of the screen.

  • 2

    Press the "Menu" button on the remote control while the lamp timer is displayed.

  • 3

    Press the left arrow button. Select "0" and wait until the timer display clears.


  • If this was helpful a vote on the thumbs up for the free advoce would be greatly appreciated. Thanks

    Apr 04, 2011 | Hitachi 60V500 60" Rear Projection...

    1 Answer

    I replaced the lamp, but am unable to reset the lamp so that the projector works again. It keeps giving me the message that I need to replace lamp and reset timer. And then it turns off.


    1. Switch power ON, and press the TIMER button on the remote controller, or the RESET button
    on the control panel, for approximately three seconds. The 'LAMP xxxx hr' message will appear
    on the lamp timer on the bottom of the screen.
    2. Press the MENU button on the remote controller, or the RESET button on the control panel,
    while the lamp timer is displayed. The 'LAMP xxxx ? 0 CANCEL' message will then
    appear.
    3. Press the and select 0, and wait until the timer display is cleared.

    Feb 18, 2011 | Hitachi CP-X270 Multimedia Projector

    1 Answer

    Our projector indicates that the light bulb needs to be replaced after replacing the light bulb once it still indicates that it needs to be replaced.


    This is the excerpt from the manual on how to reset the lamp life timer.

    Turn on the projector and use "Lamp Reset" after the lamp module is replaced.
    Lamp Reset: (i) Press "Menu" ?§ (ii) Select "Options" ?§ (iii) Select "Lamp settings" ?§ (iv) Select "Lamp Reset ?§ (v) Select "Yes".

    Jan 12, 2011 | Optoma HD65 DLP Projector

    2 Answers

    How can i see the lamp hours for mitsubishi xd300u ?


    mitsubishi doesn't have a lamp timer that can be accessed. it will have an on screen message when it gets close, and it'll turn off when it is exceeded.

    Dec 29, 2009 | Mitsubishi XD300U Multimedia Projector

    1 Answer

    How do I access service menu to reset lamp timer for Optoma H56?


    In order to reset the bulb counter you need to access the Service Menu:
    To access the Service Menu:
    Turn on and warm up
    press the following sequence:
    Up
    Up
    Left
    Give it a few goes, it took me 5 minutes to enter with the right timing. The Service Menu will appear, highlight factory reset and the counter goes to 0. Job done. Cheers, Matt.

    Apr 15, 2009 | Optoma H56 Multimedia Projector

    1 Answer

    Need to reset lamp timer


    The lamp timer expiring would not shutdown the unit typically. Purchase a replacement lamp and included will be the instructions to both replace the lamp and reset the timer.

    Dan

    Apr 15, 2009 | Mitsubishi ES100U Multimedia Projector

    2 Answers

    Lamp replacement


    Hi there

    You need to reset the lamp timer.

    Mar 11, 2008 | 3M (EP7640ILK) Projector Lamp for MP7640

    Not finding what you are looking for?
    Televison & Video Logo

    Related Topics:

    665 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Televison & Video Experts

    The Knight
    The Knight

    Level 3 Expert

    72670 Answers

    Electro Med Services...
    Electro Med Services...

    Level 3 Expert

    6694 Answers

    yadayada
    yadayada

    Level 3 Expert

    70387 Answers

    Are you a Televison and Video Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...