Question about Kodak EASYSHARE 5300 All-In-One InkJet Printer

3 Answers

Printer access door won't close

Can not get get to close.. changed cartridges,, and now can't close pinter acess door...

Posted by on

  • 1 more comment 
  • britt nicole May 27, 2008

    It says Printer Access Door is open. Please Close printer access door.
    i have opened and closed everything and it will not go away.


  • steve217 Aug 14, 2008

    having a serious problem getting the printer access door down, PRESTO just got it, very "flimsy latch if i do say so , cmon kodak you can do better than that!

  • jbsauers Aug 24, 2008

    Yes, absolutely, and nothing in online manual about how to close the "door", and since it's a weekend, no chat or phone support. So I went to Best Buy to see if they had one, they didn't; but one employee remembers having the same problem - you don't want to break it, but nothing seems to work. He said he kept trying and eventually by lifting it, etc, it did close. He doesn't know what type of printer this was, though. I don't know how many printers I've had over the last 22 years, but never had a problem lowering the door! Jeez...

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 34 Answers

Just apply force in the front of the printer access door. Don't be afraid that you might break it...

Posted on May 29, 2008

Where is that access door? i have the same problem. anyone please help!!

Posted on Aug 06, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Yes! I just tried etuckram's solution, despite my fears...it worked, and didn't break it. I actually sort of raised it up and down a few times and I guess finally got the momentum to close it. That is different than any other printer I have had...usually, you have to press the connector in, or something similar. This was just - use a little force. (Not too hard, I don't want to help anyone break their new printer!) Thanks so much, etuckram!

Posted on Aug 24, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My pinter's usb connection does not have a cartridge, how can i remove the cartirdge ?


You dont need to have USB or wireless connection to remove cartridge. Turn the printer off and on. Open the front access door. The Carriage ( that holds the cartridges ) will move to center and you can remove it.

If you are unable to remove the cartridge when the printer is on, Turn if off, Open the Carriage access door and move the carriage manually and remove it.

Regards,
Sean

Oct 06, 2013 | HP Photosmart C6180 All-In-One InkJet...

1 Answer

Cartridge door open message won't go away


see door switch your door switch have problem

May 27, 2012 | HP Office Equipment & Supplies

1 Answer

HP psc 1210 won't print. screen says i have a door open


Hello,

you need to close cartridge access door Close it
c00112062.jpg

Hope this helps,
Lucas

Jul 07, 2011 | HP Office Equipment & Supplies

1 Answer

I have to get a letter typed and don't know how to open the machine to change the ink????


  1. Open the cartridge access door. Figure 4: Open the cartridge access doorc00127636.gif
  2. Raise the cartridge latches for both cartridges. Figure 5: Raise cartridge latchesc00127637.gif
  3. Remove the protective tape from the end of the cartridges. Figure 6: Remove tapec00127639.gif
  4. Insert the cartridges into the carriage. Figure 7: Insert cartridgec00127642.gif
  5. Close the latches, and then close the cartridge access door. Figure 8: Close latchc00127644.gif The control panel displays a message prompting you to align the cartridges.
  6. Press the Enter button to start the cartridge alignment. Wait until the alignment completes before continuing.

Jun 24, 2011 | HP PSC 750 All-In-One InkJet Printer

1 Answer

Access door open


Kindly close the access door then.If you are getting the message even after closing the access door,its time to call kodak at 1800 421 6699 and the printer will be replaced free of cost for you.Access door is the door that is opened to change the cartridges.

Sep 25, 2009 | Kodak ESP 5 Printer

2 Answers

I have a kodak 5500 aio printer. I replaced the


Try the following:

1. Open the printer access door.
2. Put out both ink cartridges and the printhead.
3. Let the printer access door open.
4. Put out all paper.
5. Pull out the ac adapter at the back of the printer.
6. Wait 60 sec.
7. Pull in AC adapter.
8. Wait 30 sec. then turn on the printer
9: Wait for the error message: Printer access door open.
10. Close the printer access door.
11. Wait for the error message: Printhead is missing.
12. Open the access door and put in only the printhead and the close the access door.
13. Wait for the error message: both ink cartridges are missing.
14. Open access door, put in only the black ink cartridge, then close the acess door.
15. Wait for the error message: Color ink cartridge is missing.
16. Open access door, put in the color ink cartridge and then close the access door.

If the error is solved, do a firmwareupdate right now.

You can find it here.

Sep 22, 2009 | Kodak EASYSHARE 5500 All-In-One InkJet...

2 Answers

Error message: "Door Open"


HI there,
Follow the steps below:
Step one: Close the print cartridge access door
1.Verify that the print cartridge access door is completely closed. It may appear to be closed, but if it is not completely closed, the error message will display. Verify that there are no obstructions blocking the door.
2.If you are unsure how to close the print cartridge access door on your model, consult your User Guide for more information.
Figure 1: Examples of closing the print cartridge access door (your model may vary)
f3e57be.gif If you have attempted to completely close the access door and the error still appears, there may be a problem with the door sensor and the unit may require service.

Step two: Service your product
If you have completed all the steps listed above and are still experiencing a problem, service the product.

Good Luck!!!

neo

Feb 28, 2009 | HP OfficeJet Pro L7580 Color All-in-One...

1 Answer

Error - "Close cartidge access door"


By a door edge or  on  a hong extention
Look for a wire going to the the closing edge near thge latch or to a hinge- one of the hinged may have a curved arm  going to a micro switch buried near by

Oct 20, 2007 | HP OfficeJet G55 All-In-One InkJet Printer

Not finding what you are looking for?
Kodak EASYSHARE 5300 All-In-One InkJet Printer Logo

Related Topics:

850 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kodak Office Equipment & Supplies Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18381 Answers

Sajid Najmi
Sajid Najmi

Level 1 Expert

31 Answers

Cindy Wells

Level 3 Expert

4952 Answers

Are you a Kodak Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...