Question about Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

2 Answers

Stop working. brush was cloged. It there a reset button?

I turned it off and then turned it on again a few second later and it stopped working.
The brush was clogged with string and hair, so I cleaned it out. Still wouldn't work (10 min. later)

checked power outlets

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

I had a similar thing happen and just got off the phone with dyson. there is a resettable switch on the handle. they told me to start the vacuum in the upright position, put it in the non upright position, then push and hold in the beater bar switch which is located next to the on/off button for 10 seconds and the beater bar should start to function once again

Posted on Aug 05, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 127 Answers

Dyson has a built in mechanism to stop it from switching on if it over heats and it takes longer than 10 minutes to reset leave it cool completely then try again if this doesn't work it will need to be repaired either contact dyson or the shop where you bought and arrange to have it fixed

Posted on Jul 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Red reser button pops out after a few seconds, The brush is clear of threads.


Remove the belt from the motor to brush and then try. If the reset pops then the motor unit is faulty. If it doesn't pop off then the brush assembly is jambed or hard to turn, sometimes caused by threads in the roller endcaps

May 28, 2014 | Dyson Ball DC24 Bagless Upright Vacuum

1 Answer

My brush stop working


Barring any electrical failure or loose plug the most common cause for the vacuum brush to stop turning is belt clogged with debris or string.
Unplug the unit and check the brush for string or debris (Hair) wrapped around the pully on either end. Clear this and check the belt to make sure it has not broken, stripped or simply slipped off. Usually the bottom plate is held on with just a few screws. Easy to remove and check Belt slipped off or stripped replace. Belt slipped off you can sometimes put back on and be vacuuming in no time.
Anything wrapped around the spindle a pair of needle nose pliers comes in real handy here. If you have snagged a rug, sheet or sock etc.. check the manual for a reset button. Some vacuums have this and all it takes is clearing the chute then resetting the switch. Good luck hope this helps!

Apr 03, 2014 | Vacuums

1 Answer

The carpet sweeper on my electrolux stopped working....used it for a little bit and then it just stopped


Make sure the brush is cleared and clean, press the reset button, and try again.
If the motor runs, but the brush doesn't turn, it's likely due to a broken belt. Have it replaced by someone who knows what they're doing.
I strongly recommend taking it into an authorized shop.

Dec 04, 2010 | Electrolux Vacuums

2 Answers

I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin...


Ok, this is a "Brush Height Adjustment" issue. It will probably work great on a hard surface but on carpet the brushes bog. If you've taken the unit apart already...Sorry....do it again. When you do, you'll see a String which allows the brushes to "Float" on different surface heights. Loosen the screw a little and pull a bit more string through. Re Tighten the screw and put it together enough for a test run. Now reset the roomba.To reset the Roomba, power the Roomba on, and press the Spot, and Dock buttons together for at least 8 seconds. Until it plays a tune. The clock, and any schedule is erased at this time. Try running the Roomba with the dust bin removed to see the brushes spin easier.

Second method, is taking off the bottom cover, and removing the battery. While it's removed, and not plugged into the charger, press the clean button for at least 20 seconds. This will erase the memory. Replace battery, and cover. Run the Roomba to see if the brushes start to spin. You can also remove the brush housing by removing the 4 screws and reseating it, to see if it was a bad connection, since you have the bottom cover off.

Mar 26, 2010 | iRobot Roomba 560 Robotic Vacuum

1 Answer

HOOVER U3524 KEEPS STOPPING


its overheating check to see if its cloged any where look behind brush roller

Feb 08, 2010 | Vacuums

1 Answer

The rotator brush stopped turning. it turns fine


The brush roll will only spin when your handle is not in the locked upright position, once the handle goes upright - the brushroll de-activates

Dec 22, 2009 | Kenmore Progressive Bagless Upright with...

1 Answer

Premalite vac brush stopped turning


Not familiar with thi sbrand, but a reset is for when the brushes get jammed pr stalled, it will trip the reset. Make sure that the brsuh roll turns easily, also for a broken belt and/or bad brush roll. Some resets are for when the vac motor over heats, it will trip saving the motor. Usually this is for a jammed brush roll or a clog.

Apr 23, 2008 | LG Electronics Premalite Vacuum Bagless...

1 Answer

Rainbow SE power nozzle


If the brush is spinning ok, and the belt isn't slipping, then probably the circuit breaker is bad, or the motor is causing the problem.

Oct 23, 2007 | Rainbow 75th Anniversary Canister Vacuum

Not finding what you are looking for?
Dyson DC07 Animal Bagless Upright Cyclonic Vacuum Logo

1,149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dyson Vacuums Experts

AskDyson
AskDyson

Level 3 Expert

2572 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18394 Answers

Samyfam
Samyfam

Level 3 Expert

379 Answers

Are you a Dyson Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...