Question about Washing Machines

2 Answers

Water will not empty authomatically during wash

Posted by on

  • Anonymous Dec 28, 2008

    water fills but cycle does not run or drain

  • Anonymous Apr 21, 2009

    Washer will fill and agitate, but then won't drain.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You think that maybe the switch?

Posted on Feb 13, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Check pump for opperation / and maybe blockage in out let hose

Posted on Apr 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My west point washing machine wtw 500 fully authomatic can no longer pump water out after it has finished washing. What is wrong with it?


first thing ti check is an obstruction in the pump impeller stopping it from turning (bobby pin , coin , bra wire etc)
check for a blockage in the hose outlet

Nov 29, 2016 | Washing Machines

1 Answer

How do I fix washing machine to finish emptying during rinse and spin cycle?


Long shot, but does it fill the same as when new? I would check the atmospheric switch which is a hollow tube that runs down the inside of the drum(not in the wash cage) when the water fills, It pushes air up to stop the fill. It may have gotten clogged. Or partially clogged.

Mar 28, 2016 | Fisher and Paykel Washing Machines

1 Answer

Have WM0642HW washwer. Constantly getting dE code during each load. Hearing grinding during cycle just before dE display.


open the filter and you will find coins or some form of objects that has gone in to the wash by mistake unseen!! empty out the filter and put on wash and it will be fine! if there is water in the drum make sure you put bucket that will fit under filter to catch the water when opening the filter! or if there is a rubber tube you can drain water out from this till empty but this will take time! good luck and dont get wet

Feb 28, 2013 | LG WM0642HW 4.0 cu. ft. Front Load Washer...

1 Answer

Wont spin


Probably down to the water not emptying from the machine in the empty cycle and the machine won't spin because there's still water in the drum. If this is the case, the root of the problem is almost certainly a blocked filter, restricting the draining of the water and not allowing it all to pump out in time during the empty cycle. You probably need to find and clean your filter.

Feb 02, 2010 | Washing Machines

1 Answer

Our washing machine started leaking lots of water during the fill and empty cycles. Water pours out of front bottom left corner. Any ideas as to what is wrong?


My Maytag Ensignia washing machine leaks large amounts of water when filling and during spin cylce. What could be wrong?

Jan 04, 2010 | GE WSXH208A Front Load Washer

1 Answer

Bleach wont drain during washing


You may have a clog on that side where the water comes into it, or the dispenser valve is not opening that side.

There is a service sheet inside the bottom of that front lower access panel on the right side wall, you can go through the diagnostics to test the water flow to that side of the tray.

Feb 13, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Whirlpool Imperial


With the machine off and empty, fill the softner bin with water only. Does the water level go down or stay the same.

Nov 28, 2007 | Whirlpool Ultimate Care II LSQ9564J Top...

1 Answer

Leak coming from bottom of washing machine


It might not have totally emptied during the last cycle.  Try laying the hose where the water empties down.  The level of the hose needs to be lower than the water level to be able to drain.  Make sure you have a bucket to empty in to.

Oct 11, 2007 | Whirlpool 3.2 cu. ft. Plus Washer

Not finding what you are looking for?

Open Questions:

0 Answers

Kenmore Elite HE4T Washing Machine Diagnostic Test Didn't complete and clothes aren't spun as dry as in the past I have a Kenmore Elite HE4T washing machine and I noticed that recently it isn't getting all of the clothes completely dry from the final spin cycle. Thus, the dryer has to run through two cycles to get the clothes dry. I did a bunch of research and made sure there weren't any kinks or blockages in the drain lines; and opened up the bottom of the washer and cleaned out the drain cleanout. I found a few pennies, but everything seemed to be working ok. I ran a load and had the bottom open so that I could make sure the motor, drain and belt were all working properly. The drain does get the water out of the washer, so the clothes aren't sitting in water, they just don't seem to be spun as fast or as long as they used to. I always put it on the "extra high" spin setting no matter which type of load I run. So, I found a way to run the diagnostic test on the washer and it went through C0-C5 (the agitation step) and all worked great, until it wouldn't come out of C5 after at least 10 minutes and go thru C6-C8. I had to cancel the diagnostic test and hit the "drain and spin" button to get all of the water back out of the washer. BTW, the "drain and spin" seems to get the clothes a bit drier than when I have it run through the "normal" cycle with the "extra high" spin. If anyone has any other thoughts, I would really appreciate it. This unit is in a small space with the dryer attached so to take it out and do repairs is a pretty big hassle. It has had a new control board and two new fill valves in the 10+ years that I have owned it. Questions I have: 1.should I remove the entire drain pump to make sure there isn't anything lodged in it? 2. could it be the belt slipping slightly and keeping the spin from reaching its 1200 RPMs? 3. Anything else I may be missing???

Jan 17, 2017 | Kenmore Washing Machines

Washing Machines Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

yadayada
yadayada

Level 3 Expert

63291 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...