Question about JVC TH-M505 System

Open Question

Whenever a loud sound is played the sound turns off, I can listen to it at a very low volume like around 20 with no problems, but as soon as I turn it up the sound clicks off. It sounds like a relay in the subwofer unit but am not sure if thats exactly the problem. The fan is not working so i opened it up but the way its acting i'm not even sure if thats the problem. The dvd plays fine and all speakers work, I'm thinking it is an overheating issue, I adjusted all levels of sound to its lowest setting but it still clicks off.

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
bluenadas
  • 203 Answers

SOURCE: SubWoofer

Sounds like your original and this sub have bad amps. The amp for the sub is not the same as the amp for the other speakers. The old unit has a dead amp and this new one is on the way out. (Pulling too much current on high bass)

Posted on Jun 15, 2007

Ad
  • 1 Answer

SOURCE: Loses sound during loud moment in movie or if sound is above 30.

I want to say I used to have this same problem. Make sure you have the right speakers wired to the corresponding wiring places on the back of the sub-wolfer. If I remember correctly I had the front and rear speakers wired into the incorrect place. It would then get to a loud point in the movie and then just cut off as a safety to not blow up the speakers (I guess). May also want to try turning down the volume and replay that point in the movie until you find the sweet spot volume level if it can't be fixed.

Posted on Aug 17, 2009

  • 6 Answers

SOURCE: i cannot get sound from the tv through the

Hi, You have to make sure you are using the "audio out" from the dvd/surround into the "audio in" on your TV also in some case TVs will need to change the "input" with your remote to see where you connected your dvd/sur also some TVs have a switch for "n" or "off" for internal speakers and also you could have that option in your audio menu on your TV, Hope it help, good luck. Mike

Posted on Oct 19, 2010

tech4allmen
  • 666 Answers

SOURCE: The speaker portion of my

Hi,

This is a problem with the wiring connection. You need to check the cables make sure there are no dents or cut on them. Unplug and replug them to their designated ports. Here is the manual for your Audio System in case you don't have it. Scroll Down to page 8 for the wiring connections. CLICK HERE for the manual.

Thank you for visiting FixYa!

Posted on Jun 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix a volume / sound problem on my kustom 2x12 amp


You have a bad potentiometer which is a variable resistor. Might be the switch you are turning.

May 08, 2017 | The Audio Players & Recorders

2 Answers

The sound output is very low even using earphones can the audio output be upgraded to give a normal listening level.


Probably not without using separate amplified speakers. Check the mixer levels are set correctly.

Apr 02, 2016 | Computers & Internet

1 Answer

My amp turns on good but after a while of too much bass causes a ugly sound too loud what could it be? Can it be repaired?


If you have over driven the amp by playing it real loud with the bass control turned up, it is very possible that you have toasted the output stages of amp.
Every time you boost a tone control by 3 db you have doubled the output power at that frequency. So if you are "coasting" along at a nominal 75 watts, the moment you boost the bass by 3 db the amp has to put out 150 watts at that low frequency.. Go to +6db and now the poor amp has to kick out 300 watts! And so on.

Rule of thumb - you never use your tone controls at very loud levels. Tone controls are there to compensate for the poor frequency response of the human ear at low volume levels - the Fletcher Munsen effect. At low volumes our hearing with the lows and high frequencies so when you play something at low volume you boost up the bass and treble to compensate for poor hearing. At loud volumes our ears respond properly.

Sep 12, 2015 | Car Audio & Video

1 Answer

My crosley keepsake turntable has been having a lot of static and the sound is very low, I can only hear it if I turn the volume all the way up. I'm not sure if the needle is the problem or there is s


I would check the wires to the cartridge. It might that one or more is off or loose.
If you turn down the volume completely and listen with a record playing you should be able to hear (with your ear) the stylus in the grooves of the record playing the track. Pick a loud (rock) record for this. If it does that OK the stylus is good.

Dec 26, 2014 | Crosley Keepsake USB Turntable

1 Answer

The music volume is low


Depends what you're listening to. If the sound can be turned up in other locations in your computer, then the encoding of whatever music that you're listening to may just be low. Turn up your volume from both your master volume on your computer, and from the application from which you're playing the music.

Jun 04, 2011 | Computers & Internet

1 Answer

Turn on the car or the stereo, volume increases to really loud!!


Set the volume for how loud you would like it to turn on, then push in on the volume button for about 20 sec, that will fix it

Jul 30, 2009 | Jensen's VM9312 Car DVD Player

1 Answer

Volume Problem with my TV and Home Theater system


I had the same problem with mine.The solution I found was to use an optical audio cable rather than the red and white RCA audio jacks. Hope this helped.

Dec 23, 2008 | Sony BRAVIA® DAV-HDX576WF Theater System...

1 Answer

Bose 3.2.1 Volume is too low


ok on your receiver you have different settings this is not easiest to say and think and type at the same time so here goes

your reciever has different settings example sterio, mono expanded sound game sound etc.

i believe that if in wrong setting or the mpx is not on then you will get a low output of sound
also quite possible the songs were recorded at a lower output sound volume

i hope this made some sence

Jun 08, 2008 | Bose 3·2·1 II System

1 Answer

Denon AVR 2802 - Unit Turning Off


If DIGITAL sign blink, this mean DSP board is defective. It will cut the sound on the AMP section. DSp is maybe defective.

Jan 12, 2008 | Denon AVR-2802

1 Answer

I have a philips tv 14inch model(14pt1353)


Hi there!
It may have something to do with your "PP" or Personal Preference setting. There is a sequence you have to follow. I think you have to press "Store", then "PP", then adjust Volume to required level, then press "PP" again and then store. Try playing around with this. Regards, JUS004

Jan 01, 2008 | Zenith SY2549S TV

Not finding what you are looking for?
JVC TH-M505 System Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Audio Players & Recorders Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

The Knight
The Knight

Level 3 Expert

74383 Answers

 Grubhead
Grubhead

Level 3 Expert

5156 Answers

Are you a JVC Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...